Einhell BT-TJ 2250 Trolley Jack User Manual

1. Introduksjon

This manual provides important information for the safe and proper operation, maintenance, and troubleshooting of your Einhell BT-TJ 2250 Trolley Jack. Please read this manual thoroughly before using the product and keep it for future reference.

The Einhell BT-TJ 2250 is a robust and stable trolley jack designed for lifting vehicles with a maximum load capacity of 2250 kg. It features two ball-bearing swivel castors for easy maneuverability, an extra-large support saddle, and a long, two-part lifting rod to ensure safe and easy lifting of loads. An integrated safety valve protects against overloading.

2. Sikkerhetsinstruksjoner

Følg alltid følgende sikkerhetsregler for å forhindre skade eller skade på produktet:

• Les manualen: Before operation, read and understand all instructions and warnings in this manual.
• Lastekapasitet: Overskrid aldri den maksimale lastekapasiteten på 2250 kg.
• Stabil overflate: Always use the jack on a hard, level, and stable surface.
• Kjøretøystøtte: After lifting, always support the vehicle with appropriate jack stands before working underneath it. Never rely solely on the jack for support.
• Senterbelastning: Ensure the load is centered on the saddle of the jack.
• Tydelig område: Keep hands, feet, and other body parts clear of moving parts and the area under the load.
• Vedlikehold: Regularly inspect the jack for damage or wear. Do not use if damaged.
• Barn og kjæledyr: Hold barn og kjæledyr unna arbeidsområdet.
• Overbelastningsbeskyttelse: The jack is equipped with an overload safety valve. Do not attempt to bypass or adjust this valve.

3. Produktkomponenter

Familiarize yourself with the parts of your Einhell BT-TJ 2250 Trolley Jack:

1. Hoveddel: The robust steel frame of the jack.
2. Løftearm: The movable arm that raises the support saddle.
3. Support Saddle: The circular pad at the top of the lifting arm where the load rests. It is extra-large for stability.
4. Swivel Castors: Two ball-bearing wheels at the rear for easy steering and positioning.
5. Fixed Wheels: Two wheels at the front for stability.
6. Lifting Rod (Handle): A two-part rod used to pump the jack and operate the release valve.
7. Utløserventil: Located at the base of the lifting mechanism, controlled by rotating the lifting rod.
8. Overload Safety Valve: Internal mechanism to prevent lifting beyond the rated capacity.

4. Oppsett og montering

The Einhell BT-TJ 2250 Trolley Jack typically comes pre-assembled, but the lifting rod may need to be attached.

• Attach the Lifting Rod: Insert the two parts of the lifting rod together. Then, insert the assembled rod into the handle socket on the jack. Ensure it is securely seated.
• Bleed Air (First Use): Before first use, it is recommended to bleed any air from the hydraulic system.
  1. Turn the lifting rod counter-clockwise to fully open the release valve.
  2. Pump the lifting rod vigorously several times.
  3. Turn the lifting rod clockwise to close the release valve.

5. Bruksanvisning

5.1. Løfte en last

1. Klargjør kjøretøyet: Parker kjøretøyet på en hard, jevn overflate. Sett på parkeringsbremsen og blokker hjulene som skal forbli på bakken.
2. Plasser jekken: Locate the vehicle's designated lifting points (refer to your vehicle's owner's manual). Position the jack's support saddle directly under the lifting point.
3. Lukk utløsningsventilen: Turn the lifting rod clockwise until the release valve is fully closed. Do not overtighten.
4. Løft lasten: Pump the lifting rod up and down to raise the support saddle and lift the vehicle. Continue pumping until the vehicle reaches the desired height.
5. Sikre med jekkstativer: Immediately place appropriately rated jack stands under the vehicle's designated support points. Slowly lower the vehicle onto the jack stands by carefully turning the lifting rod counter-clockwise. Once the vehicle is securely resting on the jack stands, remove the trolley jack.

5.2. Senking av last

If the vehicle is on jack stands, first lift it slightly off the stands using the trolley jack before lowering.

1. Rydd området: Ensure no one is under or near the vehicle.
2. Plasser jekken: If removed, reposition the jack's support saddle under the lifting point.
3. Slowly Open Release Valve: Slowly and carefully turn the lifting rod counter-clockwise to open the release valve. The vehicle will begin to descend. Control the descent speed by adjusting how much you open the valve.
4. Senk helt: Continue lowering until the vehicle is fully on the ground.
5. Fjern Jack: Once the vehicle is stable on the ground, remove the trolley jack.

6. Vedlikehold og lagring

• Rengjøring: Clean the jack regularly with a damp klut. Ikke bruk sterke kjemikalier.
• Smøring: Periodically lubricate moving parts and pivot points with light machine oil.
• Hydraulisk olje: Check the hydraulic oil level periodically. If low, refill with a high-quality hydraulic jack oil. Consult a qualified technician if unsure.
• Undersøkelse: Før hver bruk, kontroller jekken for tegn på skade, lekkasjer eller slitasje. Ikke bruk en skadet jekk.
• Lagring: Store the jack in a dry, clean place, preferably with the ram fully retracted to protect the hydraulic cylinder.

7. Feilsøking

8. Spesifikasjoner

9. Garanti og støtte

For garantiinformasjon, se garantikortet som følger med produktet, eller besøk den offisielle Einhell-forhandleren. website. For technical support or spare parts, please contact Einhell customer service. Keep your purchase receipt as proof of purchase.

Einhell Customer Service: Please refer to the contact details provided on the Einhell official webnettstedet eller i produktemballasjen din.