Viqua SHO600-QL

Viqua SHO600-QL UV Lamp og bruksanvisning for Quartz Sleeve Combo Kit

1. Produktet er overview

This manual provides instructions for the Viqua SHO600-QL UV Lamp and Quartz Sleeve Combo Kit. This kit is designed for use with Viqua UV systems including models SPV-12, SPV-600, SP600-HO, and SC/SCM-600. The ultraviolet (UV) lamp and quartz sleeve are critical components for maintaining the effectiveness of your UV water treatment system, ensuring proper disinfection by emitting specific UV intensity.

2. Produktkomponenter

The Viqua SHO600-QL kit includes the following genuine Viqua components:

  • One (1) Viqua UV Lamp: A high-output ultraviolet lamp with a proprietary stepped 4-pin configuration and a grey bulb base.
  • One (1) Quartz Sleeve: A protective glass sleeve that houses the UV lamp within the UV system chamber.
Viqua SHO600-QL UV Lamp and Quartz Sleeve Combo Kit

Image 1: Viqua SHO600-QL UV Lamp and Quartz Sleeve. This image displays the two main components of the kit: the UV lamp with its grey base and 4-pin connector, and the clear quartz sleeve.

3. Viktig sikkerhetsinformasjon

Please read and understand all safety warnings before handling or installing the UV lamp og kvartshylse.

  • Elektrisk fare: Always disconnect power to the UV system before performing any maintenance or installation.
  • UV-stråling: Do not look directly at an illuminated UV lamp. Exposure to UV light can cause severe eye and skin damage.
  • Skjøre komponenter: UV lamp and quartz sleeve are made of glass. Handle with extreme care to prevent breakage.
  • Varme overflater: UV lamp and surrounding components can become hot during operation. Allow the system to cool before handling.

4. Installasjonsretningslinjer

These are general guidelines. Refer to your specific Viqua UV system's manual for detailed installation instructions.

  1. Koble fra strømmen: Turn off and unplug the UV system from its power source.
  2. Shut Off Water: Close the water supply valves to the UV system to prevent water flow.
  3. Drain System (if necessary): If replacing the quartz sleeve, drain the UV chamber to avoid water spillage.
  4. Fjern gamle komponenter: Fjern den gamle UV-lampen forsiktig.amp and quartz sleeve according to your system's instructions. Dispose of old lamps responsibly.
  5. Install New Quartz Sleeve: If replacing, gently insert the new quartz sleeve into the UV chamber. Ensure the sleeve is properly seated and sealed with the provided O-rings and retaining nut. Avoid touching the glass directly; use clean gloves or a soft cloth.
  6. Installer ny UV Lamp: Sett den nye UV l forsiktig innamp into the quartz sleeve. Align the 4-pin connector with the lamp connector on the system's power supply. Push firmly until it clicks into place.
  7. Gjenopprett vann og strøm: Slowly open the water supply valves. Check for leaks. Once confirmed, plug in and turn on the UV system.
  8. Bekreft operasjon: Confirm the UV lamp indicator light is on, indicating proper lamp funksjon.

5. Drift

Once installed and powered, the UV lamp emits ultraviolet light within the quartz sleeve. As water flows through the UV chamber, it is exposed to this UV light, which inactivates bacteria, viruses, and other microorganisms without adding chemicals to the water. The system's ballast or controller typically includes an indicator light or alarm to confirm the lamp is operating correctly or if it requires attention.

6. Vedlikehold

Regular maintenance is crucial for the continuous effectiveness of your UV system.

  • UV Lamp Erstatning: UV lamps have a limited effective life, typically 9,000 hours (approximately 12 months) of continuous operation. Even if the lamp appears to be glowing, its UV output diminishes over time. Replace the UV lamp annually to ensure consistent water disinfection.
  • Rengjøring av kvartshylser: The quartz sleeve should be cleaned periodically (e.g., every 3-6 months, or as water quality dictates) to remove any mineral deposits or fouling that can reduce UV light transmission. If the sleeve cannot be cleaned effectively, it should be replaced.
  • Use Genuine Viqua Parts: Bruk alltid original Viqua-erstatningslamps and sleeves. Non-genuine or

    Ask a question about this manual

    Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.