1. Introduksjon
Thank you for choosing the XtremepowerUS 1.0HP Variable Speed Pool Pump. This manual provides essential information for the safe installation, operation, and maintenance of your new pool pump. Please read all instructions carefully before use to ensure proper function and longevity of the product.
This pump is designed for efficient water circulation in above-ground swimming pools, hot tubs, and spas. Its robust construction and weather-resistant materials ensure reliable performance. The variable speed settings allow for optimized water transfer and energy efficiency.

Image 1.1: The XtremepowerUS 1.0HP Variable Speed Pool Pump, showing its main components including the motor, pump housing, strainer basket, and power cord.
2. Sikkerhetsinformasjon
ADVARSEL: Failure to follow these instructions can result in serious injury or death. Always consult a qualified electrician and plumber for installation if you are unsure.
- Koble alltid fra strømmen til pumpen før du utfører service eller vedlikehold.
- Ensure the pump is connected to a Ground Fault Circuit Interrupter (GFCI) protected outlet.
- Ikke bruk pumpen hvis strømledningen er skadet.
- Keep children away from the pump and all electrical connections.
- Dette produktet inneholder kjemikalier som er kjent av delstaten California for å forårsake kreft og fødselsskader eller andre reproduksjonsskader (advarsel i henhold til Proposition 65).
- Sørg for tilstrekkelig ventilasjon rundt pumpen for å forhindre overoppheting.
- Do not run the pump dry. Always ensure the pump is primed with water before operation.
3. Pakkens innhold
Kontroller at alle komponenter er til stede og uskadet ved utpakking:
- XtremepowerUS 1.0HP Variable Speed Pool Pump
- Strainer Basket (pre-installed in pump housing)
- Transparent Lid Cover for Strainer Basket
- Bruksanvisning
Note: 2pc-Union Fittings (ASIN: B01FNEQ96G) are sold separately and may be required for installation.
4. Oppsett og installasjon
4.1 Plassering
- Place the pump on a firm, level surface as close to the pool as possible to minimize friction loss from plumbing.
- Ensure the location is well-drained and protected from excessive moisture and direct sunlight.
- Allow adequate space around the pump for ventilation and future servicing.
4.2 Elektrisk tilkobling
- The pump operates on 115 Volts. Ensure your electrical supply matches this requirement.
- Connect the pump to a dedicated, properly grounded 115V outlet protected by a Ground Fault Circuit Interrupter (GFCI).
- Ikke bruk skjøteledninger.
4.3 VVS-tilkoblinger
- The pump features 1-1/2" NPT (National Pipe Taper) connections.
- Use appropriate plumbing fittings and PVC cement or thread sealant to ensure watertight connections.
- Sørg for at alle tilkoblinger er tette for å forhindre luftlekkasjer, som kan påvirke pumpens ytelse.
4.4 Grunning av pumpen
Before starting the pump for the first time or after cleaning the strainer basket:
- Sørg for at alle ventiler er åpne slik at vannet kan strømme til pumpen.
- Remove the transparent lid from the strainer basket.
- Fill the strainer basket housing completely with water.
- Replace the lid, ensuring it is securely tightened to prevent air leaks.
- Turn on the pump. It should begin to draw water and circulate. If not, repeat the priming process.

Image 4.1: The pump's oversized strainer basket, designed to capture debris and prevent clogging.
5. Bruksanvisning
5.1 Starting and Stopping the Pump
- After successful priming, plug the pump into the GFCI-protected outlet.
- The pump will start operating at the selected speed.
- To stop the pump, unplug it from the outlet or use a dedicated switch if installed.
5.2 Variable Speed Settings
This pump features two speed settings: High Flow and Low Flow. These settings allow you to adjust the water transfer rate between 1,750 and 3,450 rotations per minute (RPM).
- Høy flyt: Provides maximum circulation and is ideal for initial cleaning, backwashing, or when higher flow rates are needed.
- Lav flyt: Offers quieter operation and energy savings, suitable for routine daily filtration and maintaining water clarity.
To change the speed setting, locate the switch on the motor housing and toggle it to the desired position (HI/HAUT for High, LOW/BAS for Low).

Image 5.1: The two-speed selector switch on the pump motor for adjusting flow rate.
6. Vedlikehold
6.1 Strainer Basket Cleaning
The oversized strainer basket collects leaves and debris, preventing them from reaching the pump impeller. Regularly inspect the transparent lid to check if the basket needs cleaning.
- Slå av pumpen og koble fra strømmen.
- Rotate the transparent lid counter-clockwise to remove it.
- Løft ut silkurven.
- Empty any collected debris and rinse the basket thoroughly with water.
- Inspect the basket for cracks or damage. Replace if necessary.
- Place the clean basket back into the housing.
- Fill the housing with water to prime the pump.
- Replace the transparent lid, ensuring the O-ring is properly seated and the lid is tightened securely.
6.2 Vinterisering
In colder climates, proper winterization is crucial to prevent damage from freezing:
- Koble fra strømmen til pumpen.
- Drain all water from the pump by removing drain plugs (if applicable) or disconnecting plumbing.
- Oppbevar pumpen på et tørt og frostfritt sted utenom sesongen.
- Ensure all openings are covered to prevent insects or debris from entering.
6.3 Generell inspeksjon
- Periodically check the power cord for any signs of damage or wear.
- Inspect plumbing connections for leaks.
- Sørg for at pumpen er forsvarlig montert og fri for overdreven vibrasjon.
7. Feilsøking
Before attempting any repairs, always disconnect power to the pump.
| Problem | Mulig årsak | Løsning |
|---|---|---|
| Pumpen starter ikke | No power; tripped GFCI; motor overload | Check power connection; reset GFCI; allow motor to cool and reset thermal overload. |
| Pump runs but does not prime or has low flow | Air leak in suction line; strainer basket clogged; low water level; impeller clogged | Check all plumbing connections for leaks; clean strainer basket; ensure adequate water level in pool; inspect impeller for debris. |
| Overdreven støy eller vibrasjoner | Loose mounting; foreign object in impeller; worn bearings | Tighten mounting bolts; clear impeller; contact customer support if bearings are suspected. |
| Vann lekker fra pumpen | Loose connections; damaged O-rings/seals; cracked housing | Tighten plumbing; inspect and replace O-rings/seals; contact customer support for housing issues. |
8. Spesifikasjoner
| Trekk | Spesifikasjon |
|---|---|
| Merke | XtremepowerUS |
| Modellnummer | 75158 |
| Hestekrefter | 1.0 HK |
| Voltage | 115 volt |
| Maksimal strømningshastighet | 73 gallon per minutt (4380 GPH) |
| Hastighetsinnstillinger | 2-Speed (Variable) |
| Inn-/utløpstilkoblinger | 1-1/2" NPT |
| Produktdimensjoner (L x B x H) | 25 cm x 9 cm x 13 cm |
| Varevekt | 15 pund |
| Materiale | Metal (Motor), Plastic (Housing) |

Bilde 8.1: Dimensjonal overview of the XtremepowerUS 1.0HP Variable Speed Pool Pump.
9. Garanti og støtte
For warranty information, technical support, or to inquire about replacement parts, please contact XtremepowerUS customer service directly or refer to the product's purchase documentation. Keep your purchase receipt as proof of purchase.
For further assistance, visit the official XtremepowerUS webnettstedet eller kontakt din forhandler.