QuietWarmth THERMST-D Non-Programmable Thermostat User Manual

1. Introduksjon

The QuietWarmth THERMST-D Non-Programmable Thermostat is designed to provide reliable control for 120V or 240V electric radiant floor heating systems. This thermostat offers flexible temperature management, allowing you to configure it for control based on floor temperature, room temperature, or a combination of room temperature with a floor temperature limit. It features a built-in Ground Fault Circuit Interrupter (GFCI) for enhanced safety and a clear, backlit display for easy monitoring and operation. A floor sensor is included to ensure accurate temperature readings and optimal comfort.

Figur 1: Foran view of the THERMST-D Thermostat.

2. Sikkerhetsinformasjon

Please read all instructions carefully before installation and operation. Failure to follow these instructions may result in electric shock, fire, or property damage.

• ADVARSEL: To reduce the risk of electric shock, do not connect this device to a circuit with any phase operating down more than 150 volts to ground.
• Installasjonen må utføres av en kvalifisert elektriker i samsvar med lokale og nasjonale elektriske forskrifter.
• The thermostat requires connection to a dedicated 20 Amp krets.
• The resistive load connected to the thermostat must not exceed 15 Amps.
• Electric radiant floor heating systems are required by the National Electrical Code to be protected by a Ground Fault Circuit Interrupter (GFCI). This thermostat has a built-in GFCI.
• Slå alltid av strømmen ved sikringsbryteren før du installerer eller utfører service på termostaten.

Figur 2: Side view of the thermostat with safety warning label.

3. Pakkens innhold

Bekreft at alle varene er til stede i pakken:

• QuietWarmth THERMST-D Non-Programmable Thermostat
• Gulvføler

4. Produktet er overview

4.1 Nøkkelfunksjoner

• Non-Programmable operation for radiant floor heat systems.
• Compatible with both 120V and 240V heating systems.
• Integrated Ground Fault Circuit Interrupter (GFCI) for safety.
• Clear, backlit LED display for easy reading.
• Includes a floor sensor for precise temperature control.
• Configurable for floor temperature, room temperature, or room temperature with a floor temperature limit.
• Seven-day energy log to monitor power consumption.
• Supports multiple QuietWarmth mats: up to 120 sq ft for 120V systems, or 240 sq ft for 240V systems.

4.2 Komponenter

The thermostat consists of a front display unit with control buttons and a back plate for electrical connections.

• Frontpanel: Features a digital display showing time and temperature, along with 'Up', 'OK', and 'Down' buttons for navigation and setting adjustments.
• Bakpanel: Contains wiring terminals for power input (L1, L2) and load output, as well as a connection point for the floor sensor.

Figur 3: Bakside view of the thermostat with wiring terminals.

Figure 4: Included floor sensor.

5. Oppsett og installasjon

Installasjon skal kun utføres av en kvalifisert elektriker.

5.1 Montering

• The thermostat is designed for wall mounting.
• Ensure the mounting location is free from direct sunlight, drafts, or other heat sources that could affect temperature readings.

5.2 Kabling

Before wiring, ensure power is OFF at the circuit breaker.

1. Connect the thermostat to a dedicated 20 Amp krets.
2. Identify the Line (power supply) and Load (heating mat) wires.
3. Connect the Line wires to the L1(L) and L2(N) terminals on the thermostat's back panel.
4. Connect the Load wires from the heating mat to the 'Load' terminals on the thermostat.
5. Sørg for riktig jording i henhold til lokale elektriske forskrifter.
6. The thermostat is dual-voltage; it can be used with either 120V or 240V heating mats, but not simultaneously. Verify your heating mat's voltage samsvarer med strømforsyningen.

5.3 Floor Sensor Placement

The floor sensor is crucial for accurate floor temperature control.

• Place the sensor next to the long edge of the QuietWarmth heating mat.
• Ensure the sensor is positioned in the heated area and not near any unheated zones or external heat sources.
• Route the sensor wire carefully to avoid damage during installation of flooring materials.

Figur 5: Eksample of radiant heat film installation under floating floors.

Figur 6: Eksample of radiant heat film installation under tile and glued floors.

6. Bruksanvisning

6.1 Slå på

After installation, restore power at the circuit breaker. The thermostat display will illuminate.

6.2 Stille inn temperatur

• Bruk Up og Ned knappene for å justere ønsket temperatur.
• Trykk på OK for å bekrefte valget.

6.3 kontrollmoduser

The thermostat can be configured to operate in one of three control modes:

• Floor Temperature Control: The thermostat maintains the floor at the set temperature using the floor sensor.
• Romtemperaturkontroll: The thermostat maintains the room air temperature at the set point.
• Room Temperature Control with Floor Limit: The thermostat primarily controls room air temperature but prevents the floor temperature from exceeding a specified maximum limit, protecting sensitive flooring materials.

Refer to the full installation guide for instructions on how to select and configure these control modes.

6.4 Energy Log

The thermostat features a seven-day energy log, allowing you to monitor the power consumption of your radiant heating system. Consult the detailed manual for accessing and interpreting this data.

7. Vedlikehold

7.1 GFCI-testing

For continued safety, the built-in GFCI should be tested monthly.

1. Trykk på TEST button located on the bottom of the thermostat.
2. The GFCI should trip, cutting power to the heating system and indicating a fault.
3. Trykk på TILBAKESTILL button to restore power.
4. If the GFCI does not trip or reset correctly, discontinue use and contact a qualified electrician.

Figure 7: Bottom of the thermostat with GFCI test button.

7.2 Rengjøring

Tørk av termostatens utside med en myk klutamp klut. Ikke bruk skurende rengjøringsmidler eller løsemidler.

8. Feilsøking

If you encounter issues with your QuietWarmth THERMST-D thermostat, refer to the following common problems and solutions:

• Ingen skjerm/ingen strøm:
  • Check the circuit breaker for the dedicated circuit and ensure it is in the ON position.
  • Kontroller at alle ledningstilkoblinger er sikre og korrekte.
• Varmesystemet aktiveres ikke:
  • Ensure the thermostat is set to a temperature higher than the current room or floor temperature.
  • Check if the GFCI has tripped (press the RESET button if it has).
  • Confirm the correct control mode is selected (floor, room, or room with limit).
• GFCI Trips Frequently:
  • This indicates a ground fault. Immediately turn off power at the circuit breaker.
  • Inspect the heating mat and wiring for any damage or moisture.
  • Ensure the total resistive load does not exceed 15 Amps.
  • Contact a qualified electrician for diagnosis and repair.
• Unøyaktige temperaturavlesninger:
  • Verify the floor sensor is correctly installed and not damaged.
  • Ensure the thermostat is not exposed to drafts, direct sunlight, or other external heat sources.

For issues not covered here, please contact QuietWarmth customer support or a qualified electrician.

9. Spesifikasjoner

10. Garanti og støtte

10.1 Garantiinformasjon

The QuietWarmth THERMST-D Non-Programmable Thermostat comes with a 3-year limited warranty from the date of purchase. This warranty covers defects in materials and workmanship under normal use. Please retain your proof of purchase for warranty claims.

10.2 Kundestøtte

For technical assistance, troubleshooting, or warranty inquiries, please contact QuietWarmth customer support. Refer to the product packaging or the manufacturer's webnettstedet for oppdatert kontaktinformasjon.