Everbilt 1-1/2 Hp Thermoplastic Sprinkler Pump User Manual

1. Introduksjon

This manual provides essential information for the safe and efficient operation, installation, and maintenance of your Everbilt 1-1/2 Hp Thermoplastic Sprinkler Pump. This high-capacity pump is engineered to boost water pressure from city water sources or draw water from lakes and streams for various sprinkling and irrigation applications. It features a robust 1-1/2 HP dual voltage motor and a corrosion-resistant thermoplastic construction, ensuring durability and reliable performance. The pump is self-priming after its initial fill with water, simplifying setup.

Image 1.1: The Everbilt 1-1/2 Hp Thermoplastic Sprinkler Pump, showcasing its compact design and durable thermoplastic housing.

2. Sikkerhetsinformasjon

Les og forstå alle sikkerhetsadvarsler og instruksjoner før du installerer eller bruker denne pumpen. Unnlatelse av å følge disse instruksjonene kan føre til elektrisk støt, brann, alvorlig personskade eller død.

• Elektrisk sikkerhet: Always disconnect power before servicing the pump. Ensure the pump is properly grounded. All electrical wiring should be performed by a qualified electrician and comply with local codes. Do not operate the pump with a damaged cord or plug.
• Vannsikkerhet: Never run the pump dry, as this can cause severe damage. Protect the pump and plumbing from freezing temperatures to prevent cracking and leaks.
• Generell sikkerhet: Wear safety glasses when working with the pump. Keep children and unauthorized persons away from the operating area. Do not use this pump for flammable or corrosive liquids.

3. Pakkens innhold

Ved utpakking, kontroller at alle komponenter er til stede og uskadet. Pakken skal inneholde:

• Everbilt 1-1/2 Hp Thermoplastic Sprinkler Pump (1 unit)
• Brukerhåndbok (dette dokumentet)

4. Oppsett

Riktig installasjon er avgjørende for pumpens ytelse og levetid.

4.1 Plassering

• Install the pump on a firm, level surface to minimize vibration.
• Choose a location that is protected from direct sunlight, rain, and freezing temperatures.
• Ensure adequate ventilation around the motor for cooling.

4.2 Rørtilkoblinger

• Use appropriate pipe sizes for the inlet and outlet to ensure optimal flow and prevent cavitation.
• Apply thread sealant to all pipe connections to prevent air leaks, especially on the suction side.
• Install a foot valve with a strainer on the end of the suction line if drawing water from a lake or stream to prevent debris from entering the pump and to maintain prime.
• Install a check valve on the discharge side if necessary to prevent backflow.

4.3 Elektrisk tilkobling

• The pump features a dual voltage motor (115V or 230V). Ensure the motor is wired for the correct voltage supply available. Refer to the motor's wiring diagram for specific instructions.
• Koble pumpen til en dedikert, riktig sikret elektrisk krets.
• Sørg for at pumpen er skikkelig jordet for å unngå fare for elektrisk støt.

4.4 Grunning av pumpen

Before initial operation, the pump must be primed:

1. Remove the priming plug located on top of the pump casing.
2. Fyll pumpen casing completely with water until it overflows.
3. Sett påfyllingspluggen ordentlig igjen.
4. Ensure all valves on the suction and discharge lines are open.

5. Bruksanvisning

Once installed and primed, the pump is ready for operation.

5.1 Starte pumpen

1. Verify that all connections are tight and there are no visible leaks.
2. Ensure the suction line is submerged in water (if drawing from a source) and the discharge line is open.
3. Turn on the electrical power to the pump. The pump should start and begin moving water.
4. Monitor the pump for the first few minutes of operation for any unusual noises or vibrations.

5.2 Stoppe pumpen

To stop the pump, simply turn off the electrical power supply.

6. Vedlikehold

Regelmessig vedlikehold sikrer optimal ytelse og forlenger pumpens levetid.

6.1 Regelmessige kontroller

• Periodically inspect the pump and piping for any signs of leaks, corrosion, or damage.
• Clean any debris from the suction strainer (if applicable) to maintain proper flow.
• Ensure the motor's ventilation openings are clear of obstructions.

6.2 Vinterklargjøring (for kaldt klima)

If the pump will be exposed to freezing temperatures, it must be drained to prevent damage:

1. Koble fra strømmen til pumpen.
2. Remove the drain plug(s) from the pump casing and any low points in the piping system.
3. La alt vannet renne helt av.
4. Store the pump in a dry, protected area if possible, or ensure all plugs are reinstalled loosely to allow for air circulation.

7. Feilsøking

Denne delen inneholder løsninger på vanlige problemer du kan støte på.

8. Spesifikasjoner

Technical details for the Everbilt 1-1/2 Hp Thermoplastic Sprinkler Pump.

• Produsent: Everbilt
• Modellnummer: EFLS15-HD
• Delenummer: EFLS15-HD
• Farge: Svart
• Stil: Over bakken
• Materiale: Plast, polypropylen (PP)
• Strømkildetype: AC/DC
• Voltage: 115 Volts (AC) / 230 Volts (AC) (Dual Voltage)
• hestekrefter: 1-1 / 2 HK
• Pumpekapasitet: Up to 4020 GPH (Gallons Per Hour)
• Maximum Lifting Height (Suction Depth): Opp til 20 fot
• Antall varepakke: 1
• Varevekt: 19.5 kg
• Produktdimensjoner: 76.2 x 40.64 x 40.64 cm (Lengde x Bredde x Høyde)
• UPC: 856594003961
• Dato først tilgjengelig: 22. juni 2015

9. Garanti og støtte

For warranty information, technical support, or replacement parts, please contact Everbilt customer service. Keep your purchase receipt as proof of purchase for any warranty claims. Detailed contact information can typically be found on the product packaging or the official Everbilt webnettstedet.