Braeburn 5-2 Day Programmable Thermostat

Introduksjon

This manual provides comprehensive instructions for the installation, operation, programming, and maintenance of your Braeburn 5-2 Day Programmable Thermostat. Please read this manual thoroughly before attempting to install or operate your new thermostat.

Figur 1: Front view of the Braeburn 5-2 Day Programmable Thermostat, showing the large blue backlit display, system mode switch, fan mode switch, and programming buttons.

Funksjoner

• 5-2 Day Programmability
• Stor 2 kvm. I. Skjerm med sterkt blått bakgrunnsbelysning
• Justerbare temperaturgrenser
• Hardwire or Battery Powered (24V AC)
• Permanent minne beholder innstillinger
• Filter Sjekk Monitor
• Justerbar temperaturdifferensial
• Adaptive Recovery Mode (ARM)
• ESD Guard elektroniske kretser
• Kompressor kortsyklusbeskyttelse
• Midlertidig programoverstyring
• Programmerbar utvidet hold-modus
• Tilbakestillingsknapp for fronttilgang
• F° / C°-bryter

Installasjon og oppsett

Sikkerhetsregler

• ADVARSEL: Disconnect power to the heating and cooling system before installing or servicing the thermostat.
• Installasjonen bør utføres av en kvalifisert tekniker.
• Sørg for at ledningene er i samsvar med lokale elektriske forskrifter.

Monteringssted

Install the thermostat on an inside wall, approximately 5 feet (1.5m) above the floor. Avoid locations near heat sources (lamps, sunlight, fireplaces), drafts (windows, doors), or unconditioned spaces (unheated hallways, outside walls).

Kablingsinstruksjoner

Denne termostaten er konstruert for enkeltstage (1 Heat/1 Cool) systems. It can be powered by 24V AC hardwire or batteries.

Typical Terminations: Rc, Rh, O, B, Y1, W1, G, C

1. Slå av strømmen til HVAC-systemet ved sikringsbryteren.
2. Remove the old thermostat from the wall plate.
3. Label each wire with the terminal designation from your old thermostat.
4. Mount the new thermostat base plate to the wall.
5. Connect the labeled wires to the corresponding terminals on the new thermostat. Refer to the wiring diagram provided with your thermostat for specific connections.
6. Insert 2 AA alkaline batteries (not included) into the battery compartment if using battery power or as a backup.
7. Fest termostathuset til bunnplaten.
8. Gjenopprett strøm til HVAC -systemet.

Bruke termostaten din

Systemmodusbryter

Located on the front of the thermostat, this switch controls the overall operation mode:

• KUL: The thermostat will operate your cooling system.
• AV: Varme- og kjølesystemene er slått av.
• VARME: The thermostat will operate your heating system.

Fan Mode Switch

Located on the front of the thermostat, this switch controls the fan operation:

• BIL: Viften går bare når varme- eller kjølesystemet er aktivt.
• PÅ: Viften går kontinuerlig, uavhengig av varme- eller kjølebehov.

Stille inn temperatur

Bruk UP og NED arrow buttons on the right side of the display to adjust the desired temperature (setpoint). The display will show both the current room temperature and the setpoint.

Programming (5-2 Day)

The 5-2 day programming allows you to set different schedules for weekdays (Monday-Friday) and weekends (Saturday-Sunday). Each day can have up to 4 program periods: Morning, Day, Evening, and Night.

Stille inn tid og dag

1. Trykk på PROG button once. The display will show the current time flashing.
2. Bruk UP or NED pilene for å justere tiden.
3. Pressen PROG again to advance to the day setting. The day will flash.
4. Bruk UP or NED arrows to adjust the day.
5. Pressen PROG or wait 15 seconds to exit.

Setting Program Schedule

1. Trykk på PROG button until "MON-FRI" appears and the time for the first period (Morning) flashes.
2. Bruk UP or NED arrows to set the desired time for the Morning period.
3. Pressen PROG. The temperature for the Morning period will flash.
4. Bruk UP or NED pilene for å stille inn ønsket temperatur.
5. Repeat steps 2-4 for the Day, Evening, and Night periods for "MON-FRI".
6. After setting the "MON-FRI" schedule, press PROG to advance to "SAT-SUN" and repeat the process for weekend programming.
7. Pressen RETUR or wait 15 seconds to exit programming mode.

Midlertidig programoverstyring

To temporarily change the temperature without affecting the program, simply use the UP or NED arrows. The thermostat will hold this temperature until the next program period begins.

Permanent hold

Trykk på HOLDE button. The thermostat will maintain the current temperature indefinitely. To cancel, press HOLDE igjen eller trykk PROG to resume the schedule.

Vedlikehold

Batteribytte

When the battery indicator appears on the display, replace the 2 AA alkaline batteries immediately to ensure proper operation and prevent loss of settings. The thermostat has permanent memory, so settings will be retained during battery replacement.

1. Trekk termostathuset forsiktig vekk fra veggplaten.
2. Ta ut de gamle batteriene.
3. Insert new AA alkaline batteries, observing polarity (+/-).
4. Klikk termostathuset tilbake på veggplaten.

Rengjøring

Rengjør termostaten med en myk, damp klut. Ikke bruk skurende rengjøringsmidler eller løsemidler.

Filter Sjekk Monitor

The thermostat may feature a filter check monitor that reminds you to change your air filter. Consult your HVAC system manual for recommended filter replacement intervals.

Feilsøking

If problems persist, contact a qualified HVAC technician or Braeburn customer support.

Spesifikasjoner

Garanti og støtte

For warranty information and technical support, please refer to the documentation included with your product or visit the official Braeburn webnettstedet. Ta vare på kjøpskvitteringen som kjøpsbevis.

Produsent: Braeburn