Hampton Bay 11 ft. LED Offset Outdoor Patio Umbrella

Viktig sikkerhetsinformasjon

Vennligst les og forstå alle instruksjonene før du monterer og bruker dette produktet. Unnlatelse av å følge disse instruksjonene kan føre til personskade eller materielle skader.

• Always ensure the umbrella base is properly weighted and stable before opening the canopy.
• Do not use the umbrella in strong winds or severe weather conditions. Close and secure the canopy to prevent damage or injury.
• Hold barn og kjæledyr unna paraplyen under bruk for å unngå ulykker.
• Regularly inspect all parts for wear, damage, or loose connections. Replace damaged parts immediately.
• Ikke heng gjenstander fra paraplysrammen eller kalesjen.

Pakkeinnhold

Kontroller at alle komponenter er til stede før monteringen starter:

• Umbrella Canopy (Sunbrella Henna)
• Offset Umbrella Frame (Steel)
• Paraplybase
• Veivhåndtak
• Monteringsmaskinvare

Oppsettinstruksjoner

Trinn 1: Sett sammen basen

Place the umbrella base in the desired location on a flat, stable surface. Ensure the base is filled with sand or water as per manufacturer recommendations to provide adequate stability. The base is designed to be filled for optimal performance.

Image: The square umbrella base with a central pole receiver.

Step 2: Attach the Umbrella Frame

Insert the main pole of the umbrella frame into the receiver on the assembled base. Secure it firmly using the provided hardware (e.g., tightening knob or bolts) to ensure a stable connection.

Trinn 3: Fest kalesjen

Ensure the canopy is properly attached to the frame's arms. The LED lights are integrated into the canopy and will draw power from a solar panel located at the top of the umbrella. Allow the solar panel to charge in direct sunlight for a full day before expecting the lights to function.

Bruksanvisning

Åpne paraplyen

Locate the crank handle on the umbrella pole. Turn the crank handle clockwise to extend the canopy. Continue cranking until the canopy is fully open and taut. Do not over-crank.

Image: Close-up of the umbrella's crank lift mechanism and curved support arm.

Justering av paraplyen

This offset umbrella features a manual tilt mechanism and can be rotated. To tilt the canopy, locate the tilt adjustment lever or button on the frame and adjust to the desired angle. To rotate the umbrella, loosen the rotation lock (if present) and carefully pivot the canopy to the desired position, then re-secure the lock.

Closing and Securing the Umbrella

Turn the crank handle counter-clockwise to retract the canopy. Once fully closed, wrap the attached securing strap around the folded canopy and fasten it to prevent the umbrella from opening unexpectedly or being caught by wind.

Vedlikehold

Rengjøring

• Canopy (Sunbrella Fabric): Clean with mild soap and lukewarm water. Use a soft brush to remove dirt. Rinse thoroughly and allow to air dry completely before folding or storing. Do not use harsh chemicals or bleach.
• Ramme: Tørk av stålrammen med annonseamp cloth and mild soap. Dry thoroughly to prevent rust.

Lagring

When not in use for extended periods or during inclement weather, close and secure the umbrella. For long-term storage, consider using a protective cover or storing the umbrella indoors in a dry, sheltered area to prolong its lifespan.

Feilsøking

• Umbrella not opening/closing smoothly: Check for any obstructions in the mechanism or canopy fabric. Apply a silicone-based lubricant to moving parts if necessary.
• Umbrella unstable: Ensure the base is adequately weighted with sand or water. Verify all connections between the frame and base are tight.
• LED-lysene fungerer ikke: Ensure the solar panel has received sufficient direct sunlight to charge. Check for any debris covering the solar panel.

Spesifikasjoner

Garanti og støtte

Denne Hampton Bay product is covered by the manufacturer's warranty. For specific warranty details, claims, or technical support, please refer to the documentation included with your purchase or contact Hampton Bay customer service directly. Keep your proof of purchase for warranty purposes.