CDVI SEL2641R433NN, GALEOR1R, F1002000052

CDVI 433MHz Radio Keypad and Receiver User Manual

Model: SEL2641R433NN, GALEOR1R, F1002000052

1. Introduksjon

This manual provides detailed instructions for the installation, operation, and maintenance of the CDVI 433MHz Radio Keypad (Digicode) and its associated SEL2641R433NN 1-Relay 12V Receiver. This system is designed for secure access control applications.

Please read this manual thoroughly before attempting any installation or operation to ensure proper functionality and safety.

Figure 1: CDVI 433MHz Radio Keypad and SEL2641R433NN Receiver. The image shows the silver-colored keypad with illuminated blue numbers (0-9, A, B, C) and a transparent plastic receiver unit.

2. Sikkerhetsinformasjon

Sørg for at all strøm er frakoblet før installasjon eller vedlikehold.
Installasjonen skal kun utføres av kvalifisert personell.
Do not expose the keypad or receiver to extreme temperatures, moisture, or direct sunlight.
Use only specified power supply (12V).
Oppbevares utilgjengelig for barn.

3. Oppsett og installasjon

3.1. Komponenter overview

The system consists of two main components:

Radio Keypad (Digicode): The input device for entering access codes.
SEL2641R433NN Receiver: The unit that receives signals from the keypad and controls the access mechanism (e.g., door lock).

3.2. Montering av tastaturet

Choose a suitable mounting location, typically near the access point, ensuring it is protected from direct weather exposure if outdoors.
Mark the drilling points using the keypad's mounting plate as a template.
Bor hull og sett inn passende veggplugger.
Fest monteringsplaten til veggen.
Attach the keypad securely to the mounting plate.

3.3. Wiring the Receiver

The SEL2641R433NN receiver requires a 12V power supply and connection to the access control device. Refer to the wiring diagram below for typical connections.

Strøminngang: Connect 12V DC to the designated terminals. Observe polarity.
Reléutgang: The receiver has one relay. Connect the Normally Open (NO) or Normally Closed (NC) contacts to your access control device (e.g., electric strike, magnetic lock) as required.

(Note: A detailed wiring diagram is typically provided with the physical product. Consult it for specific terminal assignments.)

4. Bruksanvisning

4.1. Første oppstart

Once the receiver is wired and powered, it will enter a standby mode. The keypad will illuminate when a button is pressed.

4.2. Programming Access Codes

The keypad and receiver must be paired, and access codes programmed. This process typically involves:

Gå inn i programmeringsmodus: This usually involves a master code or a physical button on the receiver.
Legge til nye koder: Follow the specific sequence to input new user codes (e.g., Master Code + * + New Code + #).
Slette koder: Follow the specific sequence to remove existing user codes.
Avslutter programmeringsmodus: Save changes and exit programming mode.

(Note: Refer to the specific programming instructions provided with your product for exact key sequences and procedures, as these can vary by firmware version.)

4.3. Granting Access

To grant access, simply enter a valid programmed code on the keypad. Upon successful code entry, the receiver's relay will activate for a pre-set duration, unlocking the connected device.

5. Vedlikehold

Rengjøring: Clean the keypad surface with a soft, damp klut. Ikke bruk skurende rengjøringsmidler eller løsemidler.
Regelmessige kontroller: Periodically check all wiring connections for security and integrity, especially for the receiver unit.
Kodeadministrasjon: Regelmessig vedrview and update access codes for security purposes. Delete codes of former users.

6. Feilsøking

Problem	Mulig årsak	Løsning
Tastaturet svarer ikke.	No power to receiver or keypad not paired.	Check 12V power supply to receiver. Ensure keypad is correctly paired with the receiver.
Access code not working.	Incorrect code entered, code not programmed, or keypad/receiver not paired.	Verify code. Re-program code. Re-pair keypad and receiver.
Door/lock not activating.	Incorrect wiring to lock, faulty lock, or relay issue.	Check wiring connections. Test the lock mechanism independently. Consult a technician if relay is suspected faulty.
Kort rekkevidde eller intermitterende drift.	Radio interference or receiver antenna issue.	Check for sources of radio interference. Ensure receiver antenna is unobstructed.

7. Spesifikasjoner

Trekk	Detalj
Modellnummer	SEL2641R433NN, GALEOR1R, F1002000052
Hyppighet	433 MHz
Mottakerens strømforsyning	12V DC
Reléutgang	1 Relay (NO/NC contacts)
Tastaturtype	Radio (trådløs)
ASIN	B06VWH6V57

8. Garanti og støtte

Information regarding product warranty is typically provided with the purchase documentation or can be found on the manufacturer's official webnettstedet. Vennligst ta vare på kjøpsbeviset for garantikrav.

For technical support or further assistance, please contact CDVI customer service or your authorized dealer. Contact details can usually be found on the CDVI webnettstedet (www.cdvi.com).