Einhell Power X-Change 140Nm Cordless Impact Driver TE-CI 18/1 Li Solo - Instruction Manual

1. Introduksjon

This manual provides essential information for the safe and effective operation, setup, and maintenance of your Einhell Power X-Change 140Nm Cordless Impact Driver TE-CI 18/1 Li Solo. Please read these instructions carefully before using the tool and keep them for future reference. This product is designed for driving and removing screws and for light drilling tasks in wood and metal, utilizing its impact mechanism for high torque applications.

2. Generelle sikkerhetsinstruksjoner

Always observe the following safety precautions when using power tools to prevent electric shock, fire, and serious injury.

• Sikkerhet på arbeidsområdet: Hold arbeidsområdet rent og godt opplyst. Rotete eller mørke områder innbyr til ulykker. Ikke bruk elektroverktøy i eksplosive atmosfærer, for eksempel i nærheten av brennbare væsker, gasser eller støv.
• Elektrisk sikkerhet: Unngå kroppskontakt med jordede eller jordede overflater som rør, radiatorer, komfyrer og kjøleskap. Det er en økt risiko for elektrisk støt hvis kroppen din er jordet eller jordet.
• Personlig sikkerhet: Always wear eye protection. Use safety glasses, goggles, or a face shield. Wear hearing protection when operating the tool for extended periods. Dress properly; do not wear loose clothing or jewelry. Keep your hair, clothing, and gloves away from moving parts.
• Bruk og stell av verktøy: Ikke bruk makt på elektroverktøyet. Bruk riktig elektroverktøy til bruken. Det vil gjøre jobben bedre og tryggere med den hastigheten det er konstruert for. Koble batteriet fra elektroverktøyet før du foretar justeringer, bytter tilbehør eller oppbevarer elektroverktøy.
• Bruk og vedlikehold av batteripakke: Lad kun med laderen spesifisert av produsenten. En lader som er egnet for én type batteripakke kan skape brannfare når den brukes med en annen batteripakke. Bruk kun elektroverktøy med spesifikt utpekte batteripakker.

3. Produktet er overview og funksjoner

The Einhell TE-CI 18/1 Li Solo is a cordless impact driver designed for efficient screwdriving tasks. It is part of the Power X-Change family, allowing for interchangeable battery use with other Einhell tools.

• Høyt dreiemoment: Delivers up to 140 Nm of torque, suitable for driving large or long screws.
• Variabel hastighetskontroll: Electronic speed control allows for precise adjustment, ideal for delicate applications.
• 1/4" Hex Bit Mount: Features a 6.35 mm (1/4") hexagon fitting for quick and secure bit changes.
• Integrert LED-belysning: Three power LEDs provide optimal illumination of the work area.
• Ergonomisk design: Short, lightweight design with Softgrip surfaces ensures comfortable and tireless operation.
• Slitesterk konstruksjon: Features an aluminum housing and rubber supports for enhanced protection and ruggedness.
• Belteklips: A practical belt clip is included for convenient carrying and access during work.

Figure 1: The Einhell TE-CI 18/1 Li Solo Cordless Impact Driver, illustrating its compact design and the Power X-Change battery interface (battery sold separately).

4. Oppsett

4.1 Batteriinstallasjon (batteri og lader selges separat)

1. Ensure the battery is fully charged using an Einhell Power X-Change charger.
2. Align the battery pack with the base of the impact driver.
3. Slide the battery pack into the tool until it clicks securely into place. Ensure it is firmly seated before operation.
4. For å ta ut batteriet, trykk på utløserknappen(e) på sidene av batteripakken og skyv den ut.

4.2 Bitinnsetting og -fjerning

The impact driver uses a 1/4" (6.35 mm) hexagon fitting for impact-resistant bits.

1. Pull the quick-change chuck sleeve forward.
2. Insert the hexagon bit fully into the chuck.
3. Release the sleeve. The bit should be securely locked in place. Pull on the bit to confirm it is properly seated.
4. To remove the bit, pull the sleeve forward again and extract the bit.

Figure 2: Detail of the 1/4" hex bit mount and the three integrated LED lights, providing clear visibility of the work area.

5. Bruksanvisning

5.1 Slå av/på og hastighetskontroll

• Å starte: Press the ON/OFF switch (trigger). The integrated LEDs will illuminate the work area.
• Hastighetsjustering: The speed of the impact driver is controlled by the pressure applied to the ON/OFF switch. Pressing lightly results in lower speed, while pressing fully increases the speed up to 2300 RPM.
• Å stoppe: Slipp PÅ/AV-bryteren.

5.2 Rotasjonsretning

The direction of rotation (forward/reverse) is controlled by the selector switch located above the trigger.

• Forward Rotation (Screwing In): Push the selector switch to the left.
• Reverse Rotation (Screwing Out): Push the selector switch to the right.
• Lock Position: When the selector switch is in the middle position, the ON/OFF switch is locked, preventing accidental activation. Always engage the lock when not in use or when changing bits.

5.3 Using the Impact Driver

• Select the appropriate impact-resistant bit for your screw type and material.
• Position the bit firmly on the screw head.
• Start the tool by gently pressing the trigger, increasing pressure as needed. The impact mechanism will engage automatically when resistance is met, providing additional torque.
• Maintain a firm grip on the tool. The low reverse torque design helps reduce strain on the user.

Figure 3: An individual demonstrating the use of the Einhell impact driver for driving a screw into a wooden surface, highlighting its practical application.

6. Vedlikehold

Regelmessig vedlikehold sikrer lang levetid og optimal ytelse for slagtrekkeren din.

• Rengjøring: Etter hver bruk, rengjør verktøyhuset med en myk klutamp klut. Ikke bruk sterke kjemikalier eller slipende rengjøringsmidler. Sørg for at ventilasjonsåpningene er fri for støv og rusk.
• Lagring: Store the impact driver and battery pack in a dry, secure location, away from direct sunlight and extreme temperatures. Ensure the battery is removed from the tool before storage.
• Undersøkelse: Periodically check all screws and fasteners for tightness. Inspect the power tool for any signs of damage or wear. Do not use a damaged tool.

7. Feilsøking

8. Spesifikasjoner

9. Garanti og støtte

Einhell Power Tools come with a standard 2-year warranty. An additional 1-year warranty is available upon product registration, extending the total warranty period to 3 years. For warranty claims, technical support, or spare parts, please contact Einhell customer service or visit the official Einhell webnettstedet.

The intelligent ABS Battery Electronics and high-performance Li-Ion cells in Power X-Change batteries ensure efficiency, reliability, and durability.