1. Introduksjon
Thank you for choosing the Excalibur X600-4 4-Channel Car Amplifier. Dette amplifier is designed to provide stable and controlled power for various automotive audio systems, ensuring clear and reliable sound reproduction. This manual provides essential information for proper installation, operation, and maintenance of your amplivligere.
2. Sikkerhetsinformasjon
Les alle instruksjonene nøye før du installerer og bruker ampleverandør. Unnlatelse av å følge disse retningslinjene kan føre til skade på ampskade på kjøretøy eller personskade.
- Koble alltid fra bilens negative batteripol før du starter elektrisk arbeid.
- Sørg for riktig jording for amplifier to prevent electrical issues.
- Use appropriate wire gauges for power, ground, and speaker connections as specified.
- Unngå å montere amplifier in areas exposed to moisture or excessive heat.
- Monter sikkert ampløfteanordning for å forhindre bevegelse under kjøretøyets drift.
- Hvis du er usikker på noen av installasjonstrinnene, bør du kontakte en profesjonell installatør av bilstereo.
3. Pakkens innhold
Bekreft at alle varene er til stede i pakken:
- Excalibur X600-4 4-kanals vogn Amplivligere
- 4 festeskruer
- 2 Spare Fuses (25A)
- Brukerhåndbok (dette dokumentet)
4. Produktet er overview
The Excalibur X600-4 is a versatile 4-channel amplifier designed for enhanced in-car audio. It features:
- Maksimal effekt: 2400 watt
- RMS Power Output: 4 x 60 Watts RMS at 4 Ohms
- Bridgeable Mode: 2 x 180 Watts RMS at 4 Ohms
- 2 ohm stabil drift
- Variable høypass- og lavpassfiltre
- Frekvensrespons: 20Hz – 20kHz
- Signal-til-støy-forhold:> 88dB
- Inngangsfølsomhet: 150mV til 8V
- Low Total Harmonic Distortion: <0.1%
Amplifier-oppsett
Below are images illustrating the amplifier's design and connection points.
Figur 4.1: Øverst view of the Excalibur X600-4 ampløft, showcasing its brushed metal finish and branding.
Figure 4.2: Rear panel of the Excalibur X600-4 amplifier, showing power, ground, remote, fuse, speaker terminals, and RCA input/output connections, along with crossover and gain controls.
Figure 4.3: Graphic highlighting key features such as high power output, flexible tri-mode design, and wide frequency range.
5. Oppsett og installasjon
Proper installation is crucial for optimal performance and safety. Follow these general steps:
- Montering: Choose a dry, well-ventilated location in your vehicle, away from direct sunlight or heat sources. Secure the amplifier using the provided mounting screws. Ensure adequate space around the ampkjøler for luftsirkulasjon.
- Strømtilkobling:
- Connect the main power cable (typically 8-gauge or larger, depending on total system power) from the vehicle's positive battery terminal to the amplifier's "+12V" terminal. Install an in-line fuse holder (not supplied) within 18 inches (45 cm) of the battery.
- Connect the ground cable (same gauge as power cable) from the amplifier's "GND" terminal to a clean, unpainted metal surface on the vehicle chassis. Ensure a solid electrical connection.
- Connect the remote turn-on wire from your head unit's remote output to the amplifier's "REM" terminal. This wire turns the ampløfteren av og på med hovedenheten.
- Lydinngangstilkobling:
- Koble RCA-kabler fra hovedenhetens for-amp utganger til amplifier's "INPUT" RCA jacks (Front and Rear).
- De amplifier's input sensitivity ranges from 150mV to 8V, making it compatible with most aftermarket and some factory head units.
- Høyttalertilkobling:
- Koble høyttalerne til amplifier's speaker terminals. Pay close attention to polarity (+ and -).
- For 4-channel operation, connect one speaker per channel.
- For bridged operation (e.g., for a subwoofer), connect speakers to the designated "BRIDGE" terminals as indicated on the amplifier (refer to Figure 4.2). The amplifier is stable down to 2 Ohms in stereo mode and 4 Ohms in bridged mode.
- Førstegangs oppsett: Before turning on the system, double-check all connections. Set all gain controls to minimum and crossover settings to "FULL" or a suitable starting point.
6. Bruksanvisning
Når den er installert, juster ampLifier-innstillinger for optimal lydkvalitet.
- Gain Control (GAIN): Dette samsvarer med amplifier's input sensitivity to your head unit's output. Start with the gain at minimum. Play a familiar track at about 75% of your head unit's maximum volume. Slowly increase the ampforsterkningen til du hører forvrengning, og deaktiver deretter litt.
- Crossover Filters (HPF/LPF/FULL):
- HPF (høypassfilter): Allows frequencies above the set point to pass through. Use for full-range speakers to prevent low bass distortion.
- LPF (lavpassfilter): Allows frequencies below the set point to pass through. Use for subwoofers.
- FULL: Deaktiverer delefiltret, slik at alle frekvenser kan passere.
- Bass Boost (BASS BOOST): This control provides an increase in bass output at a specific frequency. Use sparingly to avoid distortion and speaker damage.
7. Spesifikasjoner
Detailed technical specifications for the Excalibur X600-4 amplivligere:
Figure 7.1: Graphic summarizing key performance specifications of the amplivligere.
| Trekk | Spesifikasjon |
|---|---|
| Modell | X600.4 |
| Kanaler | 4 |
| Maks effekt | 2400 watt |
| RMS-effekt (4 ohm) | 4 x 60 watt |
| RMS Power (Bridged, 4 Ohms) | 2 x 180 watt |
| Minimum impedans | 2 ohm (stereo) |
| Frekvensrespons | 20Hz–20kHz |
| Signal-til-støy-forhold | >88dB |
| Total harmonisk forvrengning (THD) | <0.1 % |
| Inndatafølsomhet | 150 mV - 8 V |
| Høypassfilter (HPF) | Variabel |
| Lavpassfilter (LPF) | Variabel |
| Anbefalte sikringer | 2 x 25A |
| Dimensjoner (L x B x H) | 365 x 220 x 48 mm (ca. 14.4 x 8.7 x 1.9 tommer) |
| Vekt | 2 kilo |
| Materiale | Metall |
Figure 7.2: Diagram illustrating the approximate dimensions of the amplivligere.
8. Feilsøking
Hvis du opplever problemer med din amplifier, se følgende vanlige problemer og løsninger:
| Problem | Mulig årsak | Løsning |
|---|---|---|
| Ingen strøm / AmpLifier slår seg ikke på | Blown fuse, poor power/ground connection, remote wire disconnected. | Check and replace fuses (use 25A). Verify all power, ground, and remote wire connections are secure and have proper voltage. |
| Ingen lydutgang | RCA cables disconnected, speaker wires disconnected/shorted, gain too low, head unit issue. | Ensure RCA cables are connected. Check speaker wire connections and for any shorts. Increase gain slowly. Test with another audio source. |
| Forvrengt lyd | Gain set too high, improper crossover settings, poor speaker connection, damaged speakers. | Reduce gain. Adjust crossover settings. Check speaker connections and impedance. Test speakers with another amplifter hvis mulig. |
| AmpOveroppheting av væske | Utilstrekkelig ventilasjon, for lav impedans, langvarig bruk av høyt volum. | Sørg for tilstrekkelig luftstrøm rundt ampVerifiser. Kontroller at høyttalerimpedansen samsvarer amplifier's capabilities. Reduce volume or allow cooling time. |
9. Vedlikehold
The Excalibur X600-4 ampLifier krever minimalt vedlikehold for å sikre langsiktig ytelse.
- Behold ampFjerneren er ren og fri for støv og rusk. Bruk en myk, tørr klut til rengjøring.
- Ensure that the cooling fins are not obstructed to maintain proper heat dissipation.
- Sjekk alle ledningsforbindelser med jevne mellomrom for tetthet og korrosjon.
10. Garanti og støtte
The Excalibur X600-4 amplifier comes with a two-year warranty, ensuring durable use and reliable operation. For technical support or warranty claims, please contact your authorized Excalibur dealer or visit the official Excalibur webnettstedet.
Vennligst ta vare på kjøpsbeviset for garantiservice.
