Satco 80-2627 Two-Light Ballast Bypass Wiring Harness Instruction Manual

1. Introduksjon

This manual provides essential instructions for the safe and correct installation, operation, and maintenance of the Satco 80-2627 Two-Light Ballast Bypass Wiring Harness. This harness is designed to convert existing fluorescent fixtures to operate with linear LED T8 lamps that require a ballast bypass (direct wire) installation. Please read all instructions thoroughly before beginning installation.

2. Sikkerhetsinformasjon

ADVARSEL: Fare for elektrisk støt. Installasjon krever kunnskap om armaturers elektriske systemer. Ikke forsøk å installere hvis du ikke er kvalifisert. Kontakt en kvalifisert elektriker.

Always disconnect power at the circuit breaker or fuse box before installation, servicing, or removing the fixture.
Sørg for at forsyningsvoltage is correct for the LED T8 lamps blir installert.
Ikke lag eller endre noen åpne hull i et kabinett med ledninger eller elektriske komponenter under installasjonen av settet.
For å forhindre skade på ledninger eller slitasje, ikke utsett ledninger for kanter på metallplater eller andre skarpe gjenstander.
This product is intended for use with specific LED T8 lamps designed for ballast bypass operation. Consult the LED lamp manufacturer's instructions for compatibility and wiring diagrams.
Bruk passende personlig verneutstyr (PPE) som vernebriller og hansker under installasjon.
Sørg for at alle koblinger er sikre og ordentlig isolert.

3. Produktet er overview

The Satco 80-2627 wiring harness simplifies the conversion of a two-lamp fluorescent fixture to operate with ballast bypass LED T8 lamps. It includes pre-wired lamp holders (sockets) and a quick-connect terminal for easy connection to the main power supply.

Satco 80-2627 Ballast Bypass Wiring Harness Components

Image 1: Components of the Satco 80-2627 Ballast Bypass Wiring Harness, showing the pre-wired lamp holders and quick-connect terminal.

4. Oppsett og installasjon

Follow these steps carefully to install the Satco 80-2627 wiring harness:

Koble fra strømmen: Turn off power to the fixture at the circuit breaker or fuse box. Verify power is off using a voltage testeren før du fortsetter.
Kabling av tilgangsarmatur: Open the fixture to access the existing ballast and wiring. Remove any covers or diffusers as necessary.
Remove Existing Ballast: Disconnect all wires from the existing fluorescent ballast. Carefully remove and dispose of the old ballast according to local regulations.
Installer ny Lamp Innehavere: Fjern eksisterende lamp holders (sockets) from the fixture. Install the new pre-wired lamp holders from the Satco 80-2627 harness into the fixture, ensuring they are securely seated.

Image 2: Illustration of the easy installation process, showing the harness with new lamp holders ready for connection.
Wire the Harness: Connect the quick-connect terminal of the Satco 80-2627 harness to the fixture's main power supply wires (Line and Neutral). Ensure proper polarity as indicated by the wiring diagram on the LED T8 lamps or fixture. Typically, one side of the LED T8 lamp receives Line voltage, and the other side receives Neutral. The harness is designed to provide these connections to the lamp holdere.
Sikker kabling: Ensure all wiring is neatly routed and secured, preventing pinching or contact with sharp edges. Replace any wiring covers.
Install LED T8 Lamps: Insert the ballast bypass LED T8 lamps into the new lamp holders. Ensure they are fully seated and twisted into place.
Close Fixture: Replace any fixture covers or diffusers that were removed.
Gjenopprett kraften: Turn power back on at the circuit breaker or fuse box. Test the new LED lighting system.

5. Bruksanvisning

Once installed, the Satco 80-2627 Ballast Bypass Wiring Harness operates seamlessly with your fixture's existing wall switch. Simply use the wall switch to turn the LED T8 lamper på eller av.

6. Vedlikehold

The Satco 80-2627 wiring harness requires minimal maintenance. Periodically, it is recommended to:

Visuell inspeksjon: With power disconnected, visually inspect the wiring and connections for any signs of wear, damage, or loose connections.
Rengjøring: If necessary, gently wipe down the exterior of the lamp holders with a dry, lint-free cloth. Do not use liquid cleaners near electrical components.

7. Feilsøking

If you encounter issues after installation, refer to the following troubleshooting guide:

Problem	Mulig årsak	Løsning
Lamps do not turn on.	Ingen strøm til armaturet. Løs ledningsforbindelse. Feil ledninger. Faulty LED T8 lamp.	Sjekk effektbryter/sikring. Verify all connections are secure (power off). Review installation steps and wiring diagram (power off). Test with a known good LED T8 lamp.
Lamps flicker or dim.	Løs lamp connection in socket. Incompatible LED T8 lamp (not ballast bypass type). Faulty LED T8 lamp.	Sørg for at lamps are fully seated and twisted. Confirm LED T8 lamps are specifically for ballast bypass applications. Replace the LED T8 lamp.

If troubleshooting steps do not resolve the issue, contact a qualified electrician or Satco customer support.

8. Spesifikasjoner

Modellnummer: 80-2627
Produsent: Satco
Delenummer: 80-2627
Produktdimensjoner: Omtrent 10 x 10 x 10 tommer (emballasje)
Varevekt: 1 pund
Strømkilde: Elektrisk med ledning
Antall Lamps Støttet: To (2)
Kompatibel Lamp Type: Linear LED T8 Lamps (Ballast Bypass / Direct Wire)
Inkluderte komponenter: Satco 80-2627 Two Light Ballast Bypass Wiring Harness

9. Garantiinformasjon

For warranty information regarding the Satco 80-2627 Two-Light Ballast Bypass Wiring Harness, please contact the manufacturer directly. Warranty terms and conditions may vary.

Produsentkontakt: Refer to Satco's official webnettstedet eller produktemballasjen for å få den mest oppdaterte kontaktinformasjonen.

10. Støtte

If you require further assistance or have questions not covered in this manual, please contact Satco customer support. Ensure you have your product model number (80-2627) available when contacting support.

Satco Webnettsted: www.satco.com