TUXING 4500Psi PCP Compressor Oil Water Filter (Model TXF02) Instruction Manual

1. Introduksjon

This manual provides essential instructions for the safe and effective use, setup, operation, and maintenance of your TUXING 4500Psi PCP Compressor Oil Water Filter, Model TXF02. This high-pressure air filter is designed to efficiently separate oil and water from compressed air, ensuring cleaner air for PCP air rifles and scuba tank filling. Constructed from aerospace aluminum with a gold anodized surface, it offers robust performance and durability.

The filter is compatible with various air pumps and compressors, capable of filtering approximately 90-95% of water and oil, and has successfully passed 50Mpa high-pressure tests. Proper adherence to these instructions will ensure optimal performance and extend the lifespan of your filter.

2. Sikkerhetsinformasjon

ADVARSEL: Unnlatelse av å følge disse sikkerhetsinstruksjonene kan føre til alvorlig personskade eller materielle skader.

• Always wear appropriate personal protective equipment, including eye protection, when handling high-pressure air systems.
• Ensure all connections are secure and leak-free before operating the filter. High-pressure leaks can be dangerous.
• Do not exceed the maximum rated pressure of 4500Psi (50Mpa) for this filter.
• Never point the filter or connected hoses at yourself or others when under pressure.
• Keep the filter away from heat sources, open flames, and flammable materials.
• Utfør regelmessig vedlikehold som beskrevet i denne håndboken for å sikre sikker drift.
• Store the filter in a clean, dry place when not in use.
• Dette produktet er ikke et leketøy. Oppbevares utilgjengelig for barn.

3. Produktet er overview og komponenter

The TUXING TXF02 Oil Water Filter is designed for deep filtration, utilizing a multi-stage system to purify compressed air. Its robust construction ensures durability and high-pressure resistance.

3.1 Nøkkelfunksjoner

• Materiale: Aerospace aluminum with gold anodized surface for corrosion resistance and durability.
• Filtreringseffektivitet: Separates 90-95% of water and oil from compressed air.
• Trykkvurdering: Tested up to 50Mpa (approximately 7250Psi), suitable for 4500Psi systems.
• Koblinger: M10*1.8mm male connector and 8mm & M10*1.8mm female quick connector for versatile compatibility.
• Multi-stage Filtrering: Includes molecular sieve, activated carbon, and moisture-resistant beads.

3.2 Komponenter

The filter system consists of the main filter housing, internal filter elements, and connection fittings.

Figure 1: TUXING Oil Water Filter with dimensions and M10*1 male and 8mm & M10*1 female quick connectors.

Figure 2: Internal filtration layers: Moisture Absorber Cotton, Activated Charcoal, Molecular Sieve, and Desiccant.

Figure 3: High-pressure resistant construction featuring aviation aluminum with an 8mm thickness.

4. Installasjonsinstruksjoner

Follow these steps to properly set up your TUXING Oil Water Filter:

1. Pakk ut komponenter: Carefully remove all items from the packaging. Verify that all components listed in the 'Included Components' section are present.
2. Inspect Filter Elements: Ensure the internal filter elements (moisture absorber cotton, activated charcoal, molecular sieve, desiccant) are correctly installed within the filter housing. Refer to Figure 2 for correct layering.
3. Connect to Compressor: Attach the M10*1.8mm male connector of the filter to the output port of your air compressor or pump. Ensure the connection is tight and secure.
4. Connect to Air Device: Connect the 8mm or M10*1.8mm female quick connector (soft hose) to your PCP air rifle, scuba tank, or other high-pressure air device.
5. Se etter lekkasjer: Before full operation, perform a low-pressure leak test. Apply a small amount of pressure and listen for hissing sounds or use a soapy water solution to detect bubbles at connection points. Tighten any leaking connections.
6. Orientering: The filter should generally be installed vertically with the air flow direction indicated (if any) or with the inlet at the top to allow gravity to assist in water separation.

Figur 4: Eksample setup showing the filter connected to a compressor.

5. Bruksanvisning

Once the filter is properly installed and all connections are secure, you can begin operation:

1. Start kompressor: Turn on your air compressor or pump according to its manufacturer's instructions.
2. Monitortrykk: Carefully monitor the pressure gauge on your compressor and the receiving air device to ensure it does not exceed the safe operating pressure.
3. Drain Water/Oil: During and after operation, periodically check the filter for accumulated water and oil. The filter is designed to separate these contaminants. Some models may have a drain valve at the bottom; if so, open it carefully to release accumulated liquids after depressurizing the system.
4. Complete Filling: Once the desired pressure is reached in your air device, turn off the compressor.
5. Depressurize and Disconnect: Safely depressurize the system before disconnecting the filter from the air device and compressor.

6. Vedlikehold

Regular maintenance is crucial for the longevity and efficiency of your TUXING Oil Water Filter. The filter elements have a lifespan of approximately 40 fills of a 6.8-liter high-pressure gas bottle.

6.1 Utskifting av filterelement

The filter includes a free set of filter cotton, which can be recycled. The molecular sieve, activated carbon, and moisture-resistant beads will also need periodic replacement.

Figure 5: Disassembled filter with replacement components including O-rings, filter cotton, desiccant, activated charcoal, and molecular sieve.

1. Trykkavlastningssystem: Ensure the filter is completely depressurized before attempting any maintenance.
2. Disassemble Filter: Carefully unscrew the ends of the filter housing to access the internal filter cartridge.
3. Remove Old Elements: Remove the used moisture absorber cotton, activated charcoal, molecular sieve, and desiccant. Dispose of them responsibly.
4. Rent hus: Clean the inside of the filter housing with a clean, dry cloth.
5. Install New Elements: Insert new filter elements in the correct order as shown in Figure 2: moisture absorber cotton, activated charcoal, molecular sieve, and desiccant.
6. Skift ut O-ringene: Inspect the O-rings for wear or damage. Replace them with new ones if necessary to ensure a proper seal.
7. Reassemble Filter: Carefully screw the filter ends back onto the housing, ensuring they are hand-tightened. Do not overtighten.
8. Test for lekkasjer: After reassembly, perform a leak test as described in the Setup Instructions before resuming full operation.

6.2 Generell pleie

• Keep the exterior of the filter clean and free from dirt and debris.
• Avoid dropping or subjecting the filter to harsh impacts.

7. Feilsøking

This section addresses common issues you might encounter with your oil water filter.

8. Spesifikasjoner

9. Garanti og støtte

For information regarding product warranty, please refer to the purchase documentation or contact your retailer. Standard return policies typically allow for returns within 30 days of purchase.

For technical support or inquiries, please contact the manufacturer, Xiamen Subang Technology Co.,Ltd., or the seller, TUXING, through your original point of purchase.