1. Produktet er overview
The Total TWP47506 750W Automatic Jet Water Pump is designed for efficient clean water collection and distribution. It is suitable for drawing water from wells, boreholes, open tanks, and other water supply sources. Primary applications include watering vegetable gardens, personal plots, and ensuring water circulation in fountains and various water features. Its design prioritizes ease of maintenance and portability, featuring an external tank location. The pump incorporates a brushless induction motor for long-lasting, maintenance-free operation. The robust cast iron pump casing can be rotated 90 degrees for flexible installation. This pump is capable of integration into automated water supply systems.
Figur 1: Total TWP47506 750W Automatic Jet Water Pump. This image shows the complete pump unit with its motor and casing.
2. Sikkerhetsinstruksjoner
Read all safety warnings and instructions carefully before operating this product. Failure to follow these instructions may result in electric shock, fire, and/or serious injury.
Generell sikkerhet
- Bruk alltid egnet personlig verneutstyr (PPE) som vernebriller og hansker.
- Sørg for at pumpen er plassert på en stabil og jevn overflate for å forhindre at den velter.
- Hold barn og uvedkommende unna driftsområdet.
- Ikke bruk pumpen i eksplosive atmosfærer, for eksempel i nærvær av brennbare væsker, gasser eller støv.
- Never use the pump to transfer flammable, corrosive, or explosive liquids.
- Disconnect the power supply before performing any maintenance, cleaning, or when the pump is not in use.
Elektrisk sikkerhet
- Sørg for at strømforsyningen voltage matches the specifications on the pump's rating label (220-240V, 50Hz).
- Use a properly grounded outlet. Do not modify the plug.
- Do not expose the pump or electrical connections to rain or wet conditions.
- Avoid using extension cords unless absolutely necessary. If an extension cord is used, ensure it is rated for outdoor use and has the correct gauge for the pump's power requirements.
- Never carry the pump by its power cord.
- Sjekk strømledningen regelmessig for skader. Hvis den er skadet, må den skiftes ut av en kvalifisert elektriker.
3. Pakkens innhold
Kontroller at alle elementene som er oppført nedenfor er til stede og uskadet ved utpakking:
- 1 x Total TWP47506 750W Automatic Jet Water Pump
- 1 x trykkbryter
- 1 x Stainless Steel Hose
- 1 x trykkmåler
- 1 x Three-way Brass Fitting
- Brukerhåndbok (dette dokumentet)
4. Tekniske spesifikasjoner
| Spesifikasjon | Verdi |
|---|---|
| Modellnummer | TWP47506 |
| Type | Self-priming Automatic Jet Pump |
| Nominell effekt | 750W (1.0 hk) |
| Voltage | 220-240V |
| Hyppighet | 50 Hz |
| Max hode | 45 meter |
| Max Flow | 60 liter / minutt |
| Maks suge | 9 meter |
| Rørdiameter | 1 x 1 tommer |
| Motortype | Copper Wire Induction Motor (Brushless) |
| Pumpehjulsmateriale | Rustfritt stål |
| Pumpe Casing Materiale | Støpejern |
| Kabellengde | 0.3 meter |
| Tank Capacity (Cylindrical) | 24 liter |
| Produktdimensjoner (L x B x H) | 30 x 19 x 22 cm |
| Varevekt | 1.5 kg |
| Farge | Sølv |
5. Oppsett og installasjon
5.1 Plassering
- Position the pump on a firm, level, and dry surface.
- Sørg for tilstrekkelig ventilasjon rundt pumpen for å forhindre overoppheting.
- Protect the pump from direct exposure to weather elements (rain, direct sunlight, frost).
- Keep the pump as close as possible to the water source to minimize suction lift and maximize efficiency.
5.2 Tilkoblingsrør
The pump is equipped with standard inch fittings for both suction and discharge pipes.
- Sugerør: Connect a rigid, airtight suction pipe (1 inch diameter) to the pump's inlet. Ensure all connections are sealed to prevent air leaks, which can affect priming and pump performance. A foot valve with a strainer should be installed at the end of the suction pipe submerged in the water source to prevent debris from entering the pump and to maintain prime.
- Utløpsrør: Connect a discharge pipe (1 inch diameter) to the pump's outlet. Use the provided three-way brass fitting, pressure switch, and pressure gauge as part of your water supply system. Ensure all connections are secure.
5.3 Grunning av pumpen
This is a self-priming pump, but initial priming is crucial for proper operation. Before first use or after the pump has run dry:
- Sørg for at sugerøret er helt nedsenket i vannkilden.
- Locate the priming plug on the top of the pump casing.
- Unscrew the priming plug and slowly fill the pump casing with clean water until it overflows.
- Replace and securely tighten the priming plug.
- Open any valves on the discharge side to allow air to escape during startup.
5.4 Elektrisk tilkobling
- Connect the pump's power cord to a grounded electrical outlet (220-240V, 50Hz).
- Ensure the electrical circuit is protected by a Residual Current Device (RCD) for added safety.
6. Drift
6.1 Starte pumpen
- Ensure the pump has been properly primed (Section 5.3).
- Verify all pipe connections are secure and leak-free.
- Plug the pump into the power outlet. The pump will start automatically if connected to an automated system with a pressure switch.
- Observe the pressure gauge. The pressure should rise as the pump builds pressure.
- If the pump does not draw water within a few minutes, switch it off, re-prime, and check for air leaks in the suction line.
6.2 Automatisk drift
When integrated into a water supply system with the included pressure switch, the pump will automatically start when water pressure drops (e.g., when a tap is opened) and stop when the desired pressure is reached (e.g., when the tap is closed). The 24-liter cylindrical tank helps maintain consistent pressure and reduces pump cycling.
6.3 Stoppe pumpen
For temporary shutdown, close all water outlets. The pump will stop automatically if operating in an automated system. For complete shutdown or extended periods of non-use, unplug the pump from the power supply.
7. Vedlikehold
Regular maintenance ensures optimal performance and extends the lifespan of your pump. Always disconnect the power supply before performing any maintenance.
7.1 Regelmessige kontroller
- Inspiser strømledningen og støpselet for tegn på skade.
- Check all pipe connections for leaks. Tighten if necessary.
- Ensure the foot valve strainer is clear of debris. Clean if clogged.
- Lytt etter uvanlige lyder under drift, da dette kan tyde på et problem.
7.2 Rengjøring
Tørk av utsiden av pumpen med adamp cloth. Do not use harsh chemicals or abrasive cleaners. Ensure the motor's ventilation openings are free from dust and debris.
7.3 Vinterklargjøring (for kaldt klima)
If the pump is exposed to freezing temperatures, it must be drained to prevent damage:
- Koble fra strømforsyningen.
- Drain all water from the pump casing by unscrewing the drain plug (if present) or by tilting the pump.
- Disconnect the suction and discharge pipes and drain them completely.
- Oppbevar pumpen på et tørt og frostfritt sted.
8. Feilsøking
Før du kontakter kundestøtte, se følgende tabell for vanlige problemer og løsninger.
| Problem | Mulig årsak | Løsning |
|---|---|---|
| Pumpen starter ikke | Ingen strømforsyning Defekt strømledning/støpsel Motor overload protection tripped |
Sjekk strømtilkobling og stikkontakt Inspiser og skift ut hvis skadet Allow motor to cool, then restart. Check for blockages. |
| Pumpen går, men det kommer ikke vann | Pumpen er ikke fylt Luftlekkasje i sugeledningen For høyt sugeløft Foot valve clogged or stuck Water source empty |
Re-prime the pump (Section 5.3) Check all suction connections for leaks and tighten Relocate pump closer to water source Clean or replace foot valve Ensure adequate water in source |
| Lav strømning eller trykk | Partial blockage in pipes/impeller Luftlekkasje i sugeledningen Slitt løpehjul Incorrect pressure switch setting |
Inspect and clear blockages Check and seal suction connections Kontakt kvalifisert servicepersonell Adjust pressure switch according to manufacturer guidelines (if adjustable) |
| Pump cycles on and off frequently | Leak in discharge system Pressure tank pre-charge incorrect Defekt trykkbryter |
Check for leaks in pipes, fittings, or fixtures Check and adjust pressure tank air pre-charge Inspect and replace pressure switch if necessary |
9. Garanti og støtte
This Total TWP47506 750W Automatic Jet Water Pump comes with a standard manufacturer's warranty. Please refer to the warranty card included with your purchase for specific terms and conditions, including warranty period and coverage details.
For technical assistance, spare parts, or warranty claims, please contact Total customer support through your retailer or visit the official Total website for contact information in your region. When contacting support, please have your model number (TWP47506) and purchase date available.