HEIMAN Z-Wave Carbon Monoxide Detector User Manual

1. Introduksjon

This manual provides essential information for the installation, operation, and maintenance of your HEIMAN Z-Wave Carbon Monoxide Detector. This device is designed to detect carbon monoxide (CO) gas and alert you to its presence, integrating with your Z-Wave smart home system for enhanced safety.

The HEIMAN Z-Wave Carbon Monoxide Detector is a compact, high-quality device, recognized as a Reddot winner in 2017. It operates on the Z-Wave 868.42 MHz frequency, suitable for the Europe version, and is compatible with various Z-Wave gateways such as Zipato, Fibaro, Vera, and SmartThings.

Figure 1: HEIMAN Z-Wave Carbon Monoxide Detector, front view.

2. Viktig sikkerhetsinformasjon

• This device is a carbon monoxide detector and is not designed to detect smoke, fire, or other gases.
• Do not paint the detector. Paint can clog the sensor openings and prevent the unit from functioning properly.
• Do not block the ventilation openings on the detector.
• Test the detector regularly as described in the "Operating" section.
• The detector requires a CR123A battery. Use only recommended battery types.
• Ikke forsøk å reparere enheten selv. Overlat all service til kvalifisert personell.
• Carbon monoxide is an invisible, odorless, and tasteless gas. This detector is designed to alert you to its presence, but it does not prevent CO from occurring.

3. Oppsett og installasjon

3.1 Installasjon av batteri

1. Twist the base of the detector counter-clockwise to open the battery compartment.
2. Insert one CR123A battery into the compartment, ensuring correct polarity (+/-).
3. Remove the protective pull tab if present.
4. Close the battery compartment by aligning the base and twisting clockwise until it clicks securely.

Figur 2: Bak view of the detector with the battery compartment open, showing the CR123A battery.

Figure 3: Inserting the CR123A battery into the detector.

3.2 Montering av detektoren

The detector can be mounted on a wall or ceiling. Carbon monoxide is slightly lighter than air and mixes readily with it. For optimal detection, install the detector:

• In or near sleeping areas.
• On every level of your home.
• At least 1.5 meters (5 feet) from fuel-burning appliances.
• Avoid mounting in corners, near windows, doors, or areas with high airflow.

1. Velg et passende sted.
2. Use the provided screws and anchors to secure the mounting plate to the wall or ceiling.
3. Attach the detector to the mounting plate by aligning it and twisting clockwise until it locks into place.

Figure 4: HEIMAN Z-Wave Carbon Monoxide Detector mounted on a ceiling.

3.3 Z-Wave Network Inclusion/Exclusion

To integrate the detector into your Z-Wave network:

1. Sett Z-Wave-gatewayen din i inkluderingsmodus (paringsmodus). Se gatewayens manual for spesifikke instruksjoner.
2. Press the Z-Wave button on the detector three times quickly. The detector will send an inclusion request to the gateway.
3. Once successfully included, the detector will appear in your gateway's device list.
4. To exclude the device, put your Z-Wave gateway into exclusion mode and press the Z-Wave button on the detector three times quickly.

4. Drift

4.1 LED Indicators and Sound Patterns

The detector uses a combination of LED flashes and beeps to indicate its status:

• Forvarming: Red LED flashes and four beeps.
• CO-alarm: Grønn LED blinker hvert 50. sekund.
• Normal Detection: Single beep every 50 seconds.
• Lavt batteri: To pip hvert 10. sekund.
• Feil: Red LED flashes every 10 seconds, with CO alarm and silent.

Note: The text on the battery in Figure 2 provides a summary of these indicators.

4.2 Testing av detektoren

It is recommended to test your CO detector weekly to ensure proper operation.

1. Trykk og hold testknappen på detektoren i noen sekunder.
2. The detector will emit a series of loud beeps and the LED will flash, indicating that the alarm and sensor are functioning correctly.
3. Release the button. The detector will return to normal operation.

5. Vedlikehold

5.1 Batteribytte

The detector is powered by one CR123A battery with an estimated lifespan of 3 years. When the battery is low, the detector will emit two beeps every 10 seconds. Replace the battery immediately when this occurs.

1. Twist the base of the detector counter-clockwise to open the battery compartment.
2. Fjern det gamle CR123A-batteriet.
3. Insert a new CR123A battery, observing correct polarity.
4. Close the battery compartment by twisting clockwise until it clicks securely.
5. Test detektoren etter batteribytte.

5.2 Rengjøring

Clean the detector regularly to prevent dust and debris from affecting its performance.

• Bruk en myk, damp cloth to wipe the exterior of the detector.
• Ikke bruk rengjøringsmidler eller løsemidler.
• Ikke mal detektoren.
• Gently vacuum around the sensor openings with a soft brush attachment to remove dust.

6. Feilsøking

7. Spesifikasjoner

• Merke: Heiman
• Modell: B0851P3WTH
• Strømkilde: 1 x CR123A batteri
• Batterilevetid: Omtrent 3 år
• Sensortype: Elektrokjemisk
• Z-Wave frekvens: 868.42 MHz (Europe Version)
• Kompatibilitet: Z-Wave Plus certified gateways (e.g., Zipato, Fibaro, Vera, SmartThings)
• Stil: Moderne
• Produsent: Heiman
• UPC: 345932281906

8. Garanti og støtte

For warranty information and technical support, please refer to the official HEIMAN webnettstedet eller kontakt din lokale distributør. Ta vare på kjøpskvitteringen som kjøpsbevis.