Lepro LE 50ft RGB 5050 LED-stripelys bruksanvisning

Introduksjon

This manual provides comprehensive instructions for the installation, operation, and maintenance of your Lepro LE 50ft RGB 5050 LED Strip Lights. Please read this manual thoroughly before installation and use to ensure proper function and safety. Keep this manual for future reference.

Sikkerhetsinstruksjoner

• Sørg for at strømforsyningen er frakoblet før installasjon eller vedlikehold.
• Dette produktet er kun beregnet for innendørs bruk. Unngå eksponering for vann eller høy luftfuktighet.
• Do not connect the LED strip to the power supply while it is still coiled on the reel. Unroll the strip completely before powering on to prevent overheating.
• Use only the provided 12V ETL-listed power adapter. Using an incompatible power supply may damage the product and void the warranty.
• Do not bend the LED strip at sharp angles (less than 90 degrees) to avoid damaging the circuit board or LEDs.
• Oppbevares utilgjengelig for barn.
• If any damage is observed on the strip or power adapter, discontinue use immediately and contact customer support.

Pakkeinnhold

Image: The complete package contents including two rolls of LED strip lights, a remote control, a power adapter, and fixing clips with screws.

Vennligst sjekk at alle varene som er oppført nedenfor er inkludert i pakken din:

• 2 x 24.6ft (total 50ft) RGB 5050 LED Strip Lights
• 1 x IR Remote Controller (44-key)
• 1 x 12V ETL-listed Power Adapter
• 1 x kontrollboks
• Festeklemmer og skruer
• Brukerhåndbok (dette dokumentet)

Spesifikasjoner

Oppsett og installasjon

Follow these steps for proper installation of your LED strip lights:

1. Klargjør overflaten:

   Before attaching the LED strip, ensure the installation surface is clean, dry, and smooth. Wipe the surface with a clean cloth to remove dust or debris. This ensures optimal adhesion of the 3M adhesive backing.

   

   Image: A hand wiping a wooden surface with a cloth, illustrating the first step of surface preparation.

2. Koble til komponentene:

   Connect the 4-pin connector from the LED strip to the control box. Ensure the arrow mark on the strip's connector aligns with the arrow mark on the control box. Then, connect the DC wire from the power adapter to the control box. Finally, plug the power adapter into a standard electrical outlet.

   

   Image: A visual guide demonstrating how to connect the DC wire to the control box and the 4-pin connector to the LED strip, emphasizing arrow alignment.

   Viktig: Ensure the "arrow" mark on the LED strip connector and the "12V" mark on the control box are on the same side for correct polarity.

   

   Image: Detail of the RGB light strip, highlighting the 10mm 4-pin connector and the strong 3M self-adhesive backing for installation.

3. Fest LED-stripen:

   Peel off the protective backing from the 3M adhesive on the back of the LED strip. Carefully press the strip onto the prepared surface, applying firm and even pressure along its entire length. For added security, use the included fixing clips and screws at regular intervals, especially around corners or areas with less adhesion.

   

   Image: A hand demonstrating how to peel and attach the LED strip to a surface, showing the adhesive backing.

4. Forberedelse av fjernkontroll:

   Before using the remote control, pull out the transparent plastic chip from the battery compartment. This activates the battery.

   

   Image: A close-up showing a hand pulling the transparent plastic chip from the remote control, indicating battery activation.

Installasjonsdemonstrasjonsvideo

Operasjon

Your LED strip lights are controlled by the included 44-key IR remote control. Point the remote directly at the IR receiver on the control box for optimal response.

Bilde: En detaljert view of the 44-key remote control, showing buttons for power, brightness adjustment, RGB color selection, 6 DIY color buttons, and various dynamic modes like Jump, Fade, Quick, Slow, and Auto.

• Slå på/av: Trykk på rød av/på-knapp for å slå lysene av eller på.
• Justering av lysstyrke: Bruk opp og ned pilknapper (above the R, G, B, W buttons) to increase or decrease brightness.
• Fargevalg: Trykk på en av 20 color buttons to select a static color.
• Gjør-det-selv-farger:
  1. Trykk på en av DIY1-DIY6 buttons.
  2. Bruk RGB up/down arrows to adjust the intensity of Red, Green, and Blue to create your desired custom color.
  3. Press the same DIY button again to save the custom color.
• Dynamiske moduser:
  • JUMP3 / JUMP7: Cycles through 3 or 7 colors with a jump effect.
  • FADE3 / FADE7: Fades between 3 or 7 colors.
  • QUICK / SLOW: Justerer hastigheten til dynamiske moduser.
  • BIL: Cycles through all available dynamic modes.
  • BLITS: Flashes through colors.

Vedlikehold

• Rengjøring: Ensure the power is off and unplugged before cleaning. Gently wipe the LED strip with a dry, soft cloth. Do not use liquid cleaners or abrasive materials.
• Lagring: If storing the lights for an extended period, ensure they are clean and dry. Store in a cool, dry place away from direct sunlight.
• Vedheft: If the adhesive begins to lose its stickiness, you can reinforce the strip with additional fixing clips or a suitable adhesive tape (not included).

Feilsøking

Garanti og støtte

Lepro products are designed for quality and reliability. For warranty information, technical support, or any questions regarding your LED strip lights, please contact Lepro customer service through the retailer where the product was purchased or visit the official Lepro webnettstedet.

Please have your model number (410105-RGB-US) and purchase details ready when contacting support.