ORIA Motion Sensor Light User Manual

1. Introduksjon

Takk for kjøpetasing the ORIA Motion Sensor Light. This battery-powered LED night light is designed to provide convenient, automatic illumination in various areas of your home. Please read this manual carefully before installation and use to ensure proper operation and longevity of your device.

2. Pakkens innhold

• 3 x ORIA Motion Sensor Night Light
• 6 x skruer
• 1 x Dobbeltsidig selvklebende tape
• 1 x brukerhåndbok

3. Spesifikasjoner

4. Sikkerhetsinformasjon

• Ikke bland gamle og nye batterier.
• Ikke bland alkaliske, standard (karbon-sink) eller oppladbare (nikkel-kadmium) batterier.
• Sørg for at batteriene er satt inn med riktig polaritet (+ og -).
• Ta ut batteriene hvis lyset ikke skal brukes over lengre tid.
• Denne enheten er kun til innendørs bruk.
• Ikke utsett for vann eller overdreven fuktighet.
• Oppbevares utilgjengelig for barn.

5. Oppsett

5.1 Installasjon av batteri

1. Vri forsiktig bakdekselet på lampen mot klokken for å åpne batterirommet.
2. Insert 3 AAA batteries (not included) into the compartment, ensuring correct polarity.
3. Replace the back cover by aligning the marks and twisting clockwise until secure.

5.2 Monteringsalternativer

The ORIA Motion Sensor Light offers two installation methods:

Image: Demonstrates the two installation methods: using screws for a permanent fixture or double-sided adhesive tape for a temporary, non-damaging mount.

Alternativ 1: Skruefeste

• Choose a desired location for the light.
• Mark the positions for the two screw holes on the mounting surface.
• Bor pilothull om nødvendig.
• Secure the light to the surface using the provided screws.

Option 2: Adhesive Tape Mounting

• Clean and dry the desired mounting surface thoroughly.
• Peel off one side of the double-sided adhesive tape and apply it firmly to the back of the light.
• Peel off the other side of the tape and press the light firmly onto the mounting surface for at least 30 seconds.
• Allow 24 hours for the adhesive to fully cure before applying significant pressure.

6. Bruksanvisning

The ORIA Motion Sensor Light features three operating modes: ON, OFF, and AUTO.

Image: Illustrates the light's behavior: off during daylight, activating upon motion detection, and automatically turning off after 30 seconds of no motion.

6.1 Modusvalg

Locate the switch on the side of the light to select your desired mode:

• PÅ: Lyset vil forbli kontinuerlig på, uavhengig av omgivelseslys eller bevegelse.
• AV: Lyset vil forbli av.
• AUTO (bevegelsessensormodus): The light will automatically turn on when motion is detected in a dark environment. It will turn off approximately 30 seconds after motion ceases.

6.2 Bevegelsessensorens funksjonalitet

Image: A motion sensor light mounted on a wall, illuminating a staircase as a person ascends, demonstrating its practical application.

• Deteksjonsvinkel: 120 grader
• Deteksjonsavstand: Opptil 9.8 fot (3 meter)
• The sensor is designed to activate only in low-light conditions to conserve battery life.
• Avoid placing the light in direct sunlight or near heat sources, as this may affect sensor performance.

7. Vedlikehold

• Rengjøring: Wipe the light with a soft, dry cloth. Do not use abrasive cleaners or immerse in water.
• Batteribytte: When the light dims or fails to activate, replace all 3 AAA batteries with new ones. Ensure correct polarity.
• Sensorpleie: Keep the motion sensor lens clean and unobstructed for optimal performance.

8. Feilsøking

9. Garanti og støtte

ORIA products are designed for reliability and performance. For warranty information or technical support, please refer to the contact details provided with your purchase or visit the official ORIA webnettstedet.

Ta vare på denne håndboken for fremtidig referanse.