AUTOWIKI Fog Lights Instruction Manual

1. Introduksjon

This manual provides detailed instructions for the installation, operation, and maintenance of your AUTOWIKI Fog Lights. These fog lights are designed to enhance visibility during adverse weather conditions such as fog, rain, or snow, contributing to safer driving. Please read this manual thoroughly before installation and use.

Image 1.1: AUTOWIKI Fog Lights for Jeep Cherokee (Driver and Passenger Side)

2. Pakkens innhold

Kontroller at alle komponentene som er oppført nedenfor er inkludert i pakken din:

• 2 x Fog Light Assemblies (Driver and Passenger Side)
• 2 x PS 12V/24W Halogen Bulbs (pre-installed)
• 1 x Wiring Kit
• 1 x Switch Group

Image 2.1: Included components: Fog lights, wiring kit, and switch group.

3. Kompatibilitet med kjøretøy

These AUTOWIKI Fog Lights are specifically designed for the following vehicle models:

• Jeep Cherokee: 2014, 2015, 2016, 2017, 2018

OEM-delenummer:

• Lamp Body: R=L 5182026AA
• Lamp Frame: (L) 68203221AA; (R) 68203220AA

Image 3.1: Vehicle compatibility for Jeep Cherokee (2014-2018).

4. Spesifikasjoner

Image 4.1: Fog light details highlighting DOT & SAE compliance and components.

Image 4.2: Detail of DOT & SAE compliance markings.

5. Installasjonsveiledning

Professional installation is recommended. If performing self-installation, ensure the vehicle is turned off and cooled down. Disconnect the battery before starting work.

5.1. Forberedelse

1. Parker kjøretøyet på et plant underlag og aktiver parkeringsbremsen.
2. Slå av motoren og ta ut nøkkelen fra tenningen.
3. Koble fra den negative polen på kjøretøyets batteri for å unngå kortslutninger.
4. Gather necessary tools (e.g., screwdrivers, wrenches, wire cutters/strippers).

5.2. Removing Existing Fog Lights (if applicable)

1. Locate the existing fog light assemblies in the front bumper.
2. Carefully remove any retaining clips, screws, or bolts securing the old fog lights.
3. Disconnect the electrical connector from the old fog light bulb.
4. Remove the old fog light assembly.

5.3. Installing New Fog Lights

1. Insert the new AUTOWIKI fog light assembly into the bumper opening. Ensure it aligns correctly with the mounting points.
2. Secure the new fog light assembly using the original retaining clips, screws, or bolts. Do not overtighten.
3. Connect the electrical connector from the vehicle's wiring harness to the new fog light bulb. Ensure a secure connection.
4. If using the included wiring kit and switch, follow the wiring diagram provided with the kit to connect the fog lights to the vehicle's electrical system and install the switch in a convenient location within the cabin.
5. Gjenta prosessen for den andre siden.

Image 5.1: Key features for installation: waterproof seal cap, light dimmer screw, and bulb with sealing ring.

Image 5.2: Detail of the electrical connector.

Bilde 5.3: Eks.ample of an installed fog light on a vehicle.

6. Drift

After installation, reconnect the vehicle battery's negative terminal. Test the fog lights before driving.

6.1. Slå på/av

• Use the installed switch to turn the fog lights on or off.
• Fog lights are typically used in conjunction with your vehicle's low beam headlights during conditions of reduced visibility.

6.2. Beam Adjustment

The fog lights feature an adjustment screw to fine-tune the beam angle for optimal visibility without blinding oncoming traffic.

1. Locate the light dimmer screw on the fog light assembly (refer to Image 5.1).
2. Using an appropriate tool, turn the screw clockwise to raise the beam or counter-clockwise to lower it.
3. Adjust the beam on a flat surface facing a wall or garage door, ensuring the light pattern is low and wide.

Image 6.1: Detail of the light dimmer adjustment screw.

Image 6.2: Illustration of fog light beam penetration.

7. Vedlikehold

Proper maintenance ensures the longevity and optimal performance of your fog lights.

7.1. Rengjøring

• Regularly clean the fog light lenses with a soft cloth and mild automotive cleaning solution.
• Avoid abrasive cleaners or harsh chemicals that could damage the polycarbonate lens material.

7.2. Bytte av pære

If a halogen bulb burns out, it can be replaced. Refer to your vehicle's service manual for specific access procedures to the fog light bulbs.

1. Ensure the vehicle is off and the lights are cool.
2. Access the rear of the fog light assembly (usually from under the bumper or wheel well).
3. Twist and remove the bulb socket from the housing.
4. Carefully pull the old bulb from the socket. Avoid touching the glass of the new bulb with bare hands; use gloves or a clean cloth.
5. Insert the new bulb into the socket and reinsert the socket into the housing, twisting to secure.

7.3. Sealing Integrity

The fog lights are designed with high-quality sealing technology for dust-proof, anti-fog, and waterproof performance. Periodically inspect the seals for any signs of damage or wear.

Image 7.1: Features highlighting the super sealing for protection against elements.

8. Feilsøking

If you encounter issues with your fog lights, refer to the following common problems and solutions:

9. Garanti og støtte

AUTOWIKI is committed to providing quality products and customer satisfaction.

9.1. Garantiinformasjon

This product comes with a 90-day after-sales satisfaction guarantee. For specific warranty terms and conditions, please refer to the documentation included with your purchase or contact AUTOWIKI customer service.

9.2. Kundestøtte

If you have any questions, require technical assistance, or need to report an issue, please contact AUTOWIKI customer support through the retailer's platform or the official AUTOWIKI website. Please have your product model number (CB30-0471-09-T1) and purchase details ready when contacting support.