Chamberlain RTXW2-10 Wireless 2-Channel Wall Transmitter

1. Produktet er overview

The Chamberlain RTXW2-10 is a wireless 2-channel wall transmitter designed for convenient control of Chamberlain roller shutter motors. Its modern and attractive design integrates seamlessly into any home environment, allowing for easy operation of individual or multiple roller shutters.

Nøkkelfunksjoner inkluderer:

• Effortless control of roller shutters without manual intervention.
• Two independent channels to operate two individual roller shutters or groups of shutters simultaneously.
• Compatibility with Chamberlain wireless roller shutter drives: RPD10ER-10, RPD15ER-10, RPD25ER-10, and RPD40ER-10.
• Can be used with the RRX1-10 radio receiver as an upgrade kit for common roller shutter motors with mechanical end limits.

Bilde 1: Foran view of the Chamberlain RTXW2-10 wireless wall transmitter, showing the control buttons for up, down, and stop functions for two channels.

2. Pakkens innhold

Vennligst sjekk at alle varene er til stede i pakken:

• 1x Chamberlain RTXW2-10 Wall Transmitter
• 1x Battery (pre-installed or separate)
• Monteringsutstyr (skruer og veggplugger)

3. Sikkerhetsinformasjon

Read all instructions carefully before installation and use. Keep this manual for future reference.

• Batterisikkerhet: Ensure correct battery polarity. Do not mix old and new batteries. Dispose of used batteries responsibly.
• Installasjon: Install the device in a dry indoor location. Avoid exposure to moisture, extreme temperatures, or direct sunlight.
• Barn: Oppbevar enheten og dens komponenter utilgjengelig for barn.
• Vedlikehold: Ikke forsøk å reparere enheten selv. Overlat all service til kvalifisert personell.

4. Oppsett og installasjon

4.1 Installasjon av batteri

The wall transmitter typically comes with a battery already installed. If not, or if replacement is needed:

1. Carefully open the battery compartment cover on the back of the transmitter.
2. Insert the lithium battery, ensuring the correct polarity (+/-) as indicated inside the compartment.
3. Lukk batteridekselet godt.

4.2 Mounting the Wall Transmitter

Choose a suitable location for the wall transmitter, typically near the roller shutter it will control, at a convenient height.

1. Separate the front panel from the mounting plate.
2. Hold the mounting plate against the wall at the desired position and mark the drilling points.
3. Bor hull på de merkede punktene og sett inn veggpluggene.
4. Fest monteringsplaten til veggen med de medfølgende skruene.
5. Snap the front panel of the transmitter onto the mounted plate.

Bilde 2: Eks.ample of a house equipped with roller shutters, illustrating the typical application environment for the wall transmitter.

5. Bruksanvisning

5.1 Pairing with Roller Shutter Motors

Before operating, the wall transmitter must be paired with your Chamberlain roller shutter motor(s) or a compatible radio receiver (e.g., RRX1-10). Refer to the specific pairing instructions for your roller shutter motor or receiver, as the process may vary. Generally, this involves:

1. Activating the programming mode on your roller shutter motor/receiver.
2. Pressing a specific button sequence on the RTXW2-10 transmitter within a short timeframe.
3. Confirming successful pairing (e.g., motor movement or LED indicator).

Note: The RTXW2-10 has two channels. You can pair one motor or a group of motors to Channel 1 and another motor or group to Channel 2.

5.2 Grunnleggende betjening

The transmitter features six buttons: two 'Up' arrows, two 'Down' arrows, and two 'Stop' buttons, arranged for two channels.

• Pil opp (^): Press to raise the roller shutter(s) assigned to that channel.
• Pil ned (v): Press to lower the roller shutter(s) assigned to that channel.
• Stopp-knapp (—): Trykk for å stoppe rulleskodden(e) i gjeldende posisjon.

To switch between channels or operate a specific channel, simply use the corresponding set of buttons.

6. Kompatibilitet

The Chamberlain RTXW2-10 wall transmitter is compatible with the following Chamberlain wireless roller shutter drives:

• Chamberlain RPD10ER-10
• Chamberlain RPD15ER-10
• Chamberlain RPD25ER-10
• Chamberlain RPD40ER-10

Additionally, it can be used as an upgrade kit in conjunction with the Chamberlain RRX1-10 radio receiver to control common roller shutter motors that have mechanical end limits.

7. Vedlikehold

7.1 Batteribytte

When the transmitter's range decreases or it becomes unresponsive, the battery may need replacement. Follow the steps in Section 4.1 for battery installation. Use a new lithium battery of the same type.

7.2 Rengjøring

Clean the surface of the transmitter with a soft, dry cloth. Do not use abrasive cleaners or solvents, as these may damage the finish or internal components.

8. Feilsøking

• Transmitter not responding:
  • Sjekk batteriet. Bytt det ut om nødvendig.
  • Ensure the transmitter is within range of the roller shutter motor/receiver.
  • Re-pair the transmitter with the motor/receiver (refer to Section 5.1).
• Roller shutter moves erratically:
  • Check for any obstructions in the roller shutter's path.
  • Verify that the motor's end limits are correctly set (refer to your motor's manual).
• Only one channel works:
  • Ensure both channels are correctly paired with their respective motors/groups.
  • Sjekk batterinivået.

9. Spesifikasjoner

10. Garanti og støtte

Chamberlain products are designed for reliability and performance. For warranty information, please refer to the documentation provided with your purchase or visit the official Chamberlain website. For technical support, troubleshooting assistance, or to inquire about spare parts, please contact Chamberlain customer service through their official channels.

Ta vare på kjøpsbeviset for garantikrav.