HelloBaby AC

HelloBaby Baby Monitor Charger Instruction Manual

For Models HB6550, HB6560, HB50-5V, and other 2022+ HelloBaby Monitors

1. Overview

This official HelloBaby replacement charger is designed to provide reliable power to your compatible HelloBaby baby monitor and camera units. It serves as an ideal accessory for replacing a lost or damaged power cord adapter, ensuring continuous monitoring of your little one.

Nøkkelfunksjoner:

  • Bred kompatibilitet: Specifically designed for HelloBaby baby monitors and cameras from 2022 and later versions, including HB6550, HB6550-2, HB6560, HB40, HB6339, HB6336, and HB6250.
  • Strømspesifikasjoner: Input: 100-240V, 50/60 Hz; Output: 5.0V, 1A.
  • Optimal lengde: Features a 6.6ft (approximately 2 meters) cable, matching the original power cord length for flexible placement.
  • Sikkerhetssertifisert: Equipped with charging safety certification to ensure safe operation.
HelloBaby baby monitor charger with a warning tag about strangulation hazard.

Figure 1: HelloBaby replacement charger with its attached warning tag. Always keep cords out of reach of children.

2. Installasjonsinstruksjoner

Follow these steps to properly set up your HelloBaby replacement charger:

  1. Bekreft kompatibilitet: Ensure your HelloBaby monitor model is listed as compatible (e.g., HB6550, HB6560, HB50-5V, HB40, HB6339, HB6336, HB6250). If unsure, refer to your monitor's manual or contact HelloBaby support.
  2. Connect to Monitor/Camera: Insert the small connector end of the charger cable into the designated power port on your HelloBaby baby monitor or camera unit.
  3. Koble til strømuttaket: Plug the AC adapter end of the charger into a standard 100-240V wall outlet.
  4. Bekreft lading: The monitor or camera should indicate that it is receiving power or charging (e.g., a charging icon on the screen or an LED indicator).
Close-up of the power adapter showing input and output specifications: 100-240V, 50-60Hz, 0.2A input, and 5.0V, 1.0A output.

Figure 2: Power adapter details, confirming 5V 1A output for safe charging.

Video 1: This video demonstrates the HelloBaby monitor's features, including its setup and use, which involves connecting the power adapter for charging and continuous operation.

3. Drift

Once connected, the charger will automatically begin supplying power to your HelloBaby monitor or camera. For optimal battery life, it is recommended to keep the monitor plugged in when not in active use or when the battery level is low. The charger is designed for continuous use.

4. Stell og vedlikehold

To ensure the longevity and safe operation of your charger, please observe the following:

  • Håndteres med forsiktighet: Avoid bending or twisting the cable excessively, especially near the connectors, to prevent internal wire damage.
  • Hold tørr: Do not expose the charger to water or excessive humidity.
  • Rengjør forsiktig: If cleaning is necessary, unplug the charger from the wall and wipe it with a dry, soft cloth. Do not use liquid cleaners.
  • Lagring: Når den ikke er i bruk, oppbevar laderen på et kjølig og tørt sted, unna direkte sollys og ekstreme temperaturer.
  • Sikkerhetsadvarsel: The charger cable includes a warning tag regarding strangulation hazards. Always keep the cord out of reach of children (more than 3 feet / 0.9 meters away). Do not remove this tag.

5. Feilsøking

If your monitor or camera is not charging, perform the following diagnostic steps:

  • Sjekk strømuttaket: Sørg for at stikkontakten fungerer ved å koble til en annen enhet.
  • Inspiser tilkoblinger: Verify that both ends of the charger are securely plugged into the monitor/camera and the wall outlet.
  • Swap Cords (if applicable): If you have two original power cords (e.g., one for the monitor, one for the camera), try swapping them between devices. If a device works with the swapped cord, then the original cord for that device may be faulty, and this replacement charger is needed.
  • Kontakt kundestøtte: If the issue persists after these steps, contact HelloBaby customer support for further assistance or warranty claims.

6. Produktspesifikasjoner

TrekkDetalj
MerkeHei kjære
ModellnummerAC
KoblingstypeAC
Kompatible enheterHelloBaby Baby Monitors (HB6550, HB6550-2, HB6560, HB50, HB6339, HB6250, HB40, HB6336)
Inngang Voltage100-240V (AC)
Utgang Voltage5.0V
Ampslette1 Amps
Wattage5 watt
Kabellengde6.6 fot (ca. 2 meter)
SpesialfunksjonKortslutningsbeskyttelse
FargeHvit
Varevekt0.317 unser

7. Garantiinformasjon

This HelloBaby replacement charger comes with a one-year warranty from the date of purchase. This warranty covers manufacturing defects and ensures the product functions as intended under normal use. Please retain your proof of purchase for any warranty claims.

8. Kundestøtte

For any questions, concerns, or technical assistance regarding your HelloBaby baby monitor charger, please contact HelloBaby customer support. You can typically find contact information on the HelloBaby official webnettstedet eller gjennom forhandleren der du kjøpte produktet.

© 2026 HelloBaby. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.