Schneider Electric Square D X Series 15 Amp Dimmer Light Switch User Manual

1. Viktig sikkerhetsinformasjon

ADVARSEL: Fare for elektrisk støt. Improper installation can result in serious injury or death. Always turn off power at the circuit breaker or fuse box before wiring. Installation should only be performed by a qualified electrician or trained personnel. Ensure all local and national electrical codes are followed.

• Koble fra strømmen ved sikringsbryteren før installasjon eller service.
• Bruk en berøringsfri voltage testeren for å bekrefte at strømmen er av.
• Do not use with non-dimmable loads.
• Kun for innendørs bruk.
• Driftstemperaturområde: 32°F til 140°F (0°C til 60°C).

2. Pakkens innhold

Pakken din skal inneholde følgende vare:

• Square D X Series 15 Amp Dimmer Light Switch (SQR22601LA)

3. Spesifikasjoner

4. Installasjon

This section provides step-by-step instructions for installing your Square D X Series Dimmer. Refer to the embedded video for a visual guide.

4.1. Trinn før installasjon

1. Slå av strømmen: Locate your circuit breaker panel and turn off the power to the switch you are replacing or the circuit where you are installing the new dimmer.
2. Bekreft at strømmen er av: Bruk en riktig klassifisert voltage sensing device to confirm that the power is completely off at the switch box.
3. Identifiser ledninger: Carefully pull the existing switch out of the wall box. Identify the wires: ground (bare copper or green), hot (black, usually connected to the line side), load (black, usually connected to the light fixture), and neutral (white, if present). The Square D dimmer wires are labeled on the back of the device.

4.2. Tilkobling av dimmeren

Use the included wire nuts. For stranded device wires and solid house wires, securely wrap the stranded wires around the solid wires with lineman's pliers before tightening the wire nuts.

1. Koble til jordledning: Connect the house green or bare copper ground wire to the green ground wire on the dimmer.
2. Koble til varm ledning: Connect the black house hot wire to the black hot wire on the dimmer.
3. Koble til lastledningen: Connect the remaining black house load wire to the load wire on the dimmer.
4. Connect Neutral Wire (if applicable): If your installation requires a neutral connection, connect the house neutral wire to the neutral wire on the dimmer.

4.3. 3-Way Circuit Wiring (if applicable)

If you are wiring the dimmer in a 3-way circuit, you will need to add a single-pole switch on the far end. Follow the wiring identification as shown in the diagram below. The dimmer will connect to the traveler and neutral wires from the single-pole switch.

Image: 3-Way Wiring Diagram. This diagram illustrates the connections for a 3-way dimmer setup, showing the dimmer, a light fixture, and a single-pole switch with their respective wiring paths.

4.4. Siste trinn

1. Insert Dimmer: Carefully insert the wired dimmer into the wall box, ensuring no wires are pinched against the device or the box.
2. Secure Dimmer: Bruk de medfølgende skruene for å feste dimmeren til veggboksen.
3. Gjenopprett strøm og test: Turn the power back on at the circuit breaker. Test the dimmer to ensure it functions correctly.
4. Installer veggplate: Install the appropriate Square D X Series wall plate (not provided) over the dimmer. It should snap into place for a flush finish.

5. Drift

The Square D X Series Rocker Dimmer offers intuitive control over your lighting.

Image: Dimmer Operation. A hand is shown pressing the rocker switch of the dimmer, demonstrating how to adjust light levels.

• Slå på/av: Press the top of the rocker to turn the lights on to the last set brightness. Press the bottom of the rocker to turn the lights off.
• Juster lysstyrke: To dim or brighten the lights, press and hold the top of the rocker for increasing brightness, or press and hold the bottom of the rocker for decreasing-lysstyrke.
• Luftgap-bryter: The small slider on the side or bottom of the dimmer acts as an air gap switch, completely disconnecting power to the light fixture for bulb replacement or maintenance.

6. Adjusting Dimming Range

To optimize performance and prevent flickering with certain LED or CFL bulbs, you may need to adjust the dimmer's low-end trim setting.

1. Set to Full Brightness: Slide the dimmer all the way to the top for full brightness.
2. Dim Gradually: Slowly slide the dimmer down until the light starts to flicker or just before the bulb turns off.
3. Adjust Setting Wheel: If flickering occurs, locate the small setting wheel (trim adjustment) on the side of the dimmer. Adjust this wheel slightly up or down until the flickering stops and the light dims smoothly to your desired minimum level.

7. Vedlikehold

The Square D X Series Dimmer is designed for long-lasting, maintenance-free operation.

• Rengjøring: To clean the dimmer and wall plate, wipe with a soft, damp klut. Ikke bruk skurende rengjøringsmidler eller løsemidler.
• Ingen deler som kan repareres av brukeren: There are no user-serviceable parts inside the dimmer. Do not attempt to open or repair the device.

8. Feilsøking

9. Garanti og støtte

This Schneider Electric Square D X Series Dimmer comes with a 2 års produsentgaranti.

For technical support or warranty claims, please contact Schneider Electric customer service. Refer to the product packaging or the official Schneider Electric webnettsted for kontaktinformasjon.