FLYLINKTECH BD10 6000A 12V Car Jump Starter and Power Bank User Manual

1. Introduksjon

Thank you for choosing the FLYLINKTECH BD10 6000A 12V Car Jump Starter and Power Bank. This device is designed to provide emergency jump-starting for vehicles and serve as a portable power bank for various electronic devices. Please read this manual thoroughly before use to ensure safe and optimal operation.

Image 1.1: The FLYLINKTECH BD10 Jump Starter unit with its smart battery clamps.

2. Sikkerhetsinformasjon

Always observe the following safety precautions to prevent injury or damage to the device or vehicle:

• Ikke forsøk å starte et frossent batteri med startkabler.
• Sørg for riktig polaritetstilkobling (rød kabel)amp til positiv, svart klamp to negative). Reverse polarity can cause damage.
• Do not allow the smart clamps å berøre hverandre når de er koblet til jumpstarteren.
• Hold enheten unna barn.
• Do not expose the device to extreme temperatures (above 60°C / 140°F or below -20°C / -4°F) or direct sunlight for extended periods.
• Ikke demonter eller modifiser enheten.
• Use only the provided smart clamps and charging cables.
• Hvis enheten blir for varm under bruk, må du koble den fra umiddelbart.

Image 2.1: The jump starter incorporates multiple safety features such as spark-proof, reverse polarity, overvoltage, short circuit, overload, and high-temperature protection.

3. Pakkens innhold

Bekreft at alle varene er til stede i pakken:

• FLYLINKTECH BD10 Jump Starter Unit
• Smart batteri Clamps
• USB-C til USB-C-kabel
• USB-A til USB-C-kabel
• 12V DC Car Charger Adapter
• Brukerhåndbok
• Oppbevaringsboks

Image 3.1: The complete package includes the jump starter, smart clamps, various cables, user manual, and a protective storage case.

4. Oppsett og lading

4.1 Innledende lading

Before first use, fully charge the jump starter. The device features a 26800mAh battery capacity.

• Connect the provided USB-C cable to the jump starter's USB-C input port.
• Connect the other end of the cable to a compatible USB wall charger (not included). For fastest charging, use a PD 45W charger.
• The LED screen will display the charging status and battery percentage.

4.2 Ladetider

Note: A 45W wall charger is not included in the package.

Image 4.1: The device supports PD 45W fast charging, significantly reducing recharge time when using a compatible charger.

5. Bruksanvisning

5.1 Hoppstart av et kjøretøy

The FLYLINKTECH BD10 is capable of jump-starting all gas engines and diesel engines up to 12.0L.

1. Sørg for tilstrekkelig lading: Check the jump starter's LED screen to ensure it has at least 50% charge.
2. Connect Smart Clamps: Sett inn den blå pluggen på smarttelefonenamps into the jump starter's 12V output port. Ensure a firm connection.
3. Koble til bilbatteri:
   • Fest rød (+) clamp til kjøretøyets positive batteripol.
   • Fest svart (-) clamp to the vehicle's negative battery terminal.
4. Sjekk indikator: Den smarte clamp indicator light should turn solid green, indicating a correct connection. If it flashes or shows red, check connections and battery status.
5. Press BOOST (if needed): If the vehicle battery is extremely low or completely dead, press the 'BOOST' button on the jump starter. Wait for the indicator light on the smart clamps to turn solid green.
6. Start kjøretøy: Attempt to start your vehicle. If it doesn't start on the first try, wait 30 seconds before trying again. Do not attempt more than 3 consecutive starts.
7. Fjern Clamps: Når kjøretøyet starter, fjern smartklokken umiddelbart.ampfra bilbatteriet, og koble dem deretter fra starthjelpen.

Image 5.1: The jump starter connected to a car battery, ready for operation. It supports 6000A peak current, 12V output, and is suitable for a wide range of engines.

Image 5.2: Visual guide illustrating the four steps to jump-start a vehicle: connect the plug, attach clamps, press boost, and start the engine.

5.2 Powerbank-funksjon

The BD10 can charge multiple electronic devices via its USB-A and USB-C ports.

• USB1-utgang: Opptil 18 W (maks.)
• USB2-utgang: Opptil 18 W (maks.)
• USB-C-utgang: Opptil 45 W (PD)

Connect your device using the appropriate USB cable to the desired output port. The LED screen will show 'OUT' and the wattage being drawn.

Image 5.3: The jump starter functioning as a power bank, simultaneously charging a smartphone and a tablet via its USB ports.

5.3 LED lommelykt

The built-in LED flashlight offers three modes: constant light, SOS signal, and strobe light.

• Press and hold the flashlight button to turn on the constant light.
• Press the button again to cycle through SOS and strobe modes.
• Trykk og hold igjen for å slå av.

Image 5.4: The integrated LED flashlight provides illumination, an SOS signal, and a strobe function for emergency situations.

5.4 Informative LED Screen

The 6.0-inch LED screen provides real-time information about the device's status:

• Batterinivå: Viser gjenværende batteriprosenttage.
• IN/OUT Indicator: Shows whether the device is charging (IN) or discharging (OUT).
• Wattage Display: Indicates the power (W) being drawn or supplied.
• Feiladvarsler: Displays specific error codes or symbols if an issue occurs.

Image 5.5: The 6.0-inch LED screen provides clear information on battery percentage, input/output status, and power consumption.

6. Vedlikehold

• Lad opp regelmessig: For å forlenge batteriets levetid, lad opp jumpstarteren hver 3.–6. måned, selv om den ikke er i bruk.
• Lagring: Store the device in its protective case in a cool, dry place, away from direct sunlight and moisture.
• Rengjøring: Tørk av enheten med en myk, tørr klut. Ikke bruk sterke kjemikalier eller slipende materialer.
• Clamp Omsorg: Sørg for smartklokkenamps are clean and free of corrosion before and after each use.

7. Feilsøking

The device features multiple alarm situations indicated by audible signals and screen displays:

• Lav Voltage Beskyttelse: Audible signal "3". Recharge the device.
• Eksternt voltage Exceeds Vehicle Voltage: Audible signal "4". Check vehicle battery voltage.
• Kortslutningsbeskyttelse: Audible signal "5". Check clamp connections for short circuits.
• Safety Mode Activated: Audible signal "6". Device has entered safety mode due to an issue.
• Overstrømsbeskyttelse: Audible signal "7". Reduce load or check connections.
• Høy/lav temperaturalarm: Audible signal "8". Allow device to return to operating temperature range (-20°C to 60°C).
• Reverse Connection: Audible signal "9". Correct the clamp polaritet.

Bilde 7.1: Overview of the device's multi-alarm system, indicating various protection states with unique audible signals.

Hvis problemene vedvarer etter at du har fulgt disse trinnene, kan du kontakte kundestøtte.

8. Spesifikasjoner

Image 8.1: The device is designed to operate reliably in extreme climates, from -20°C (-4°F) to 60°C (140°F).

9. Garanti og støtte

FLYLINKTECH is committed to providing high-quality products. For any questions, technical assistance, or warranty claims, please refer to the contact information provided with your purchase or visit the official FLYLINKTECH webnettstedet. Vennligst ta vare på kjøpsbeviset av garantihensyn.