Andeman 4000A Jump Starter (Model EP-166) User Manual

1. Introduksjon

Thank you for choosing the Andeman 4000A Jump Starter, Model EP-166. This device is designed to provide reliable power for jump-starting vehicles and charging electronic devices. Please read this manual thoroughly before use to ensure safe and optimal operation.

1.1. Hva er i esken

• Epower-166 Jump Starter Unit x1
• Smart Clamps x1
• Type-C ladekabel x1
• Brukerhåndbok x1
• Oppbevaringsboks x1

Image: All components included in the Andeman Jump Starter package, laid out for clear visibility.

2. Sikkerhetsregler

Your safety is paramount. This device incorporates advanced safety features, but proper handling is crucial. The Andeman EP-166 is UL Certified, ensuring it meets stringent safety standards.

2.1. Integrated Safety Protections

The intelligent safety terminals feature 10 advanced protections:

• Overbelastningsbeskyttelse
• Gnistbeskyttelse
• Beskyttelse mot omvendt lading
• Omvendt polaritetsbeskyttelse
• Overstrømsbeskyttelse
• Beskyttelse ved lav temperatur
• Overladingsbeskyttelse
• Kortslutningsbeskyttelse
• Over Voltage Beskyttelse
• Beskyttelse mot høy temperatur

Bilde: En intern view highlighting the 10 advanced safety protections integrated into the Andeman Jump Starter for secure operation.

2.2. Miljøhensyn

• Temperaturområde: The device is engineered to operate in extreme temperatures, from -20°C (-4°F) to 60°C (140°F).
• Vanntetthetsvurdering: With an IP65 waterproof rating, the unit is resistant to rain and splashes. Avoid submerging the device in water.
• Varighet: The design is drop-proof and sand-proof for enhanced durability in various environments.

3. Oppsett

3.1. Lading av starthjelpen

Before initial use, fully charge the jump starter. It features Type-C 3.0A Quick Charging technology, allowing a full charge from 0% to 100% in approximately 1.8 hours. Each complete charge provides up to 80 jump-starts.

• Connect the provided Type-C charging cable to the jump starter's input port.
• Koble den andre enden av kabelen til en passende USB-strømadapter (ikke inkludert).
• LED-displayet vil vise ladefremdriften.

Image: The jump starter being fast-charged via its Type-C port inside a vehicle, showing its quick recharge capability.

4. Bruksanvisning

4.1. Hoppstart av et kjøretøy

1. Sørg for at starthjelpen er tilstrekkelig ladet.
2. Sett inn smartklamps cable into the jump starter's dedicated port.
3. Koble til den røde (+) clamp til den positive polen på kjøretøyets batteri.
4. Koble til den svarte (-) clamp til den negative polen på kjøretøyets batteri.
5. Check the indicator light on the smart clamps. A solid green light indicates it's safe to proceed. If it flashes red or beeps, refer to the troubleshooting section.
6. Start kjøretøyets motor.
7. Once the vehicle starts, remove the smart clamps from the vehicle battery within 30 seconds.
8. Koble fra smarttelefonenamps cable from the jump starter.

Image: The Andeman Jump Starter connected to a car battery, illustrating the ease of use for jump-starting a vehicle.

4.2. Bruk som powerbank

The 20000mAh capacity allows the jump starter to function as a power bank for various electronic devices.

• Connect your device's charging cable to one of the available USB output ports (USB-A: 2.1A; 5V/9V/12V or USB-B: 3A; 5V/2.1A).
• The dedicated Type-C port can also charge laptops at speeds comparable to their original adapters.
• LED-skjermen viser den gjenværende batteriprosententage.

Image: The 20000mAh power bank feature in action, charging a laptop, smartphone, tablet, headphones, and smartwatch.

4.3. Bruk av LED-lommelykten

The built-in ultra-bright LED flashlight offers three lighting modes:

• Lommelykt: For general illumination (e.g., inspecting an engine, changing a tire).
• SOS: A life-saving signal light for emergencies.
• Strobe: A traffic warning light to alert oncoming traffic.

To activate and cycle through the modes, press the dedicated flashlight button on the unit.

Image: Illustration of the three versatile LED lighting modes: standard flashlight, SOS signal, and strobe, useful for various emergencies.

5. Vedlikehold

5.1. Lading og lagring

• Recharge the jump starter every 3-6 months if it is not in regular use to maintain battery health.
• Store the device in its protective storage box in a cool, dry place, away from direct sunlight and extreme temperatures.

6. Feilsøking

Den smarte clamps provide visual and audible feedback to help diagnose common issues:

7. Spesifikasjoner

8. Offisielle produktvideoer

9. Garanti og støtte

For detailed warranty information and customer support, please refer to the user manual included in your product package. You may also contact Andeman customer service directly via email: andeman@andeman.com.