RGBlink NDI PTZ Camera Controller (RGBBKT) User Manual

1. Introduksjon

This manual provides detailed instructions for the setup, operation, maintenance, and troubleshooting of the RGBlink NDI PTZ Camera Controller (RGBBKT). This device is designed for professional video production environments, offering comprehensive control over various PTZ cameras using multiple protocols.

Image 1.1: RGBlink NDI PTZ Camera Controller (RGBBKT).

2. Oppsett

Follow these steps to set up your RGBlink NDI PTZ Camera Controller.

2.1 Utpakking og førstegangsinspeksjon

• Fjern forsiktig alle komponenter fra emballasjen.
• Kontroller at alle varene som er oppført på pakkelisten er til stede.
• Inspect the controller for any signs of physical damage. If damage is found, contact your dealer immediately.

2.2 Koble til kontrolleren

The RGBlink NDI PTZ Camera Controller supports various connection methods for power and camera control.

• Power over Ethernet (PoE): Connect a single RJ45 Ethernet cable from a PoE-enabled network switch to the controller's LAN port. This provides both power and network connectivity.
• Ekstern strømadapter: If PoE is not available, connect the provided power adapter to the DC 12V input port and to a power outlet.
• Kameratilkoblinger:
  • Ethernet (IP Control): Connect PTZ cameras to the same network as the controller via RJ45 Ethernet cables. The controller supports VISCA over IP, ONVIF v2.42, and NDI v5.5 protocols.
  • Serial Control: For cameras supporting serial communication, use RS232, RS422, or RS485 interfaces. Connect the appropriate cables from the controller's serial ports to the cameras.

Image 2.1: Rear panel connections including RS-232, RS-422, LAN (PoE), and Power Input.

Bilde 2.2: Eks.ample connection diagram showing PTZ Controller, PoE Switch, PTZ Cameras, Audio Mixer, and Computer.

Image 2.3: Diagram illustrating IP camera connections via a network switch.

2.3 Nettverkskonfigurasjon

For IP-based camera control, ensure the controller and cameras are on the same network segment. The controller supports automatic detection of NDI-enabled PTZ cameras.

• Access the controller's web grensesnitt ved å skrive inn IP-adressen i en web browser. (Refer to the device's display or network tools to find the IP address).
• The default login credentials are typically 'admin' with a blank password. It is recommended to set a strong password immediately.
• Innenfor web interface, configure camera protocols (e.g., ONVIF, VISCA over IP) and enter camera-specific user credentials if required.

Image 2.4: NDI|HX camera search and control interface on the controller.

3. Drift

This section details the operational functions of the RGBlink NDI PTZ Camera Controller.

3.1 Overview av kontroller

The controller features a 3.49" LCD display, a 3D joystick, various knobs, and a numeric keypad for intuitive control.

Image 3.1: The controller's 3.49-inch LCD display.

Bilde 3.2: Detaljert view of the 3D joystick and multi-function knobs.

Image 3.3: Layout of the controller's buttons and numeric keypad area.

3.2 Kameravalg

• Hurtigvalgknapper: Use the dedicated CAM 1-5 buttons for quick selection of up to 5 cameras.
• Numerisk tastatur: For cameras beyond the quick select buttons (up to 255), press the CAM-ID button, then enter the camera number using the numeric keypad, and press GÅ.

Image 3.4: The controller's ability to manage multiple cameras.

3.3 PTZ-kontroll

• joystick: The 3D joystick controls pan (left/right), tilt (up/down), and zoom (rotate the joystick).
• PT hastighetsknapp: Adjusts the gimbal movement speed for pan and tilt.
• Zoom Knob: Provides precise zoom control, especially useful in preview modus.

3.4 Image Parameter Adjustment

• IRIS/SHUTTER Knob: Rotate to adjust aperture and shutter speed. Press to switch control modes.
• R/B GAIN Knob: Rotate to adjust red and blue gain. Press to switch control modes.
• FOCUS Button: Trykk på AUTOFOKUS button to switch the camera to auto focus mode.
• EXPOSURE Button: Cycles through exposure modes (Aperture Priority, Shutter Priority, Gain Priority, Manual Exposure, Auto Exposure).
• BACKLIGHT Button: Toggles the camera's backlight mode.
• WHITE BALANCE CYCLE Button: Cycles through white balance modes (Indoor, Outdoor, Manual, Auto).
• ONE PUSH TRIGGER Button: When white balance is set to "One-Push White Balance", press this button to initiate a one-push white balance calibration.

Image 3.5: Functions of buttons and knobs on the left side of the controller.

Image 3.6: Functions of buttons and knobs on the right side of the controller, including preset controls.

3.5 forhåndsinnstillinger

• SET PRESET Button: Press to enter preset position mode. Use the numeric keys to enter the preset number (0-9) and press GÅ å redde. trykk ESC å gå ut.
• CALL PRESET Button: Press to enter preset recall mode. Use the numeric keys to enter the preset number (0-9) and press GÅ to recall. Press ESC å gå ut.
• The controller supports saving and recalling up to 255 presets per camera.

3.6 Menynavigasjon

• MENY-knapp: Press to open or close the camera settings menu. In menu control mode, the joystick controls navigation (up, down, left, right), GÅ confirms selections, and ESC acts as a back button.

4. Vedlikehold

Proper maintenance ensures the longevity and optimal performance of your RGBlink NDI PTZ Camera Controller.

4.1 Rengjøring

• Use a soft, dry cloth to clean the exterior of the controller.
• For gjenstridig smuss, litt dampen the cloth with water or a mild, non-abrasive cleaning solution.
• Avoid using harsh chemicals, solvents, or abrasive materials, as these can damage the surface and display.
• Ensure no liquids enter the device through openings or ports.

4.2 Oppbevaring

• Når kontrolleren ikke er i bruk over lengre tid, må den oppbevares kjølig og tørt, unna direkte sollys og ekstreme temperaturer.
• Beskytt enheten mot støv og fuktighet.

5. Feilsøking

Denne delen inneholder løsninger på vanlige problemer du kan støte på.

5.1 Ingen strøm

• Sjekk strømkilden: Ensure the power adapter is securely connected to both the controller and a working power outlet.
• PoE-sjekk: If using PoE, verify that the Ethernet cable is connected to a PoE-enabled port on your network switch and that the switch is powered on.
• Kabelintegritet: Inspect the power cable and Ethernet cable for any damage.

5.2 Cannot Control Camera

• Nettverkstilkobling: For IP cameras, ensure the controller and cameras are on the same network and can communicate. Check network cables and IP addresses.
• Protokoll uoverensstemmelse: Verify that the correct control protocol (e.g., VISCA over IP, ONVIF, NDI, Pelco-D/P) is selected on both the controller and the camera.
• Kamera-ID: Ensure the correct camera ID is selected on the controller.
• Påloggingsinformasjon: If the camera requires authentication, confirm that the correct username and password are configured in the controller's web grensesnitt.
• Seriell tilkobling: For serial control, check RS232/RS422/RS485 cable connections and ensure baud rates and addresses match between the controller and camera.
• Fastvare: Ensure both the controller and cameras have the latest firmware installed. Visit the RGBlink support webnettsted for oppdateringer.

5.3 LCD Display Issues

• Ingen visning: Sørg for at kontrolleren er slått på.
• Dim skjerm: Check if there are any brightness settings on the controller that can be adjusted.

6. Spesifikasjoner

Image 6.1: Controller dimensions and typical usage environments.

Image 6.2: Visual representation of supported protocols including RJ45, RS485, RS422, RS232, ONVIF, NDI, Pelco-D, Pelco-P, and Visca.

7. Produktvideodemonstrasjon

Watch the official product video for a visual demonstration of the RGBlink NDI PTZ Camera Controller's features and operation.

8. Garanti og støtte

For warranty information, technical support, or service inquiries, please contact RGBlink customer service or visit their official webnettstedet.

• Produsent: Xiamen RGBlink Vitenskap og Teknologi Co., Ltd.
• Offisiell Webnettsted: www.rgblink.com (Merk: Dette er en plassholder URLSe produktemballasjen eller den offisielle dokumentasjonen for riktig støtte. webnettstedet.)
• Kontaktinformasjon: Refer to the RGBlink official website for the most current contact details for technical support and warranty claims.