LTECH KMS1 Switch Module Owner’s Manual

LTECH KMS1 Switch Module

Produktintroduksjon

• Fully supports major smart home ecosystems including Apple Home, SmartThings, Google Assistant, and Amazon, enabling unified management across platforms.
• Built-in Thread module, compatible with the Matter protocol, supports Siri, Google, and Alexa voice control.
• Supports OTA firmware updates to continuously receive the latest features and security patches, ensuring long-term device stability.
• Parameter settings for switch type and power-on status can be completed via the NFC Lighting App.
• Reserved mechanical switch/reset switch interface accommodates both traditional operating habits and smart scenario requirements.

Tekniske spesifikasjoner

Produktbilder

DIMENSJON

• Enhet: mm
• Dimensjoner: 45 x 45.5 x 20.5

Koblingsskjema

1.  Mechanical Switch Wiring Diagram
   Includes connections for load, line (L), and neutral (N).
2.  Push Switch Wiring Diagram
   Includes connections for load, line (L), and neutral (N).

Bruk NFC Lighting APP
Scan the QR code with your mobile phone and install the APP as prompted. Compatible with iOS 13 or above and Android NFC-enabled models.

Read the Device
Click “Read/Write LED driver” in the APP [home page], place the sensing area of the phone near the NFC identification point of the driver, and read the device parameters.

Rediger parametere
Click “Parameter Management” to select the switch type. When selecting a reset switch, you can configure the device’s power-on state function.

Add to Matter Platform Instructions

1. This device supports control via major smart home platforms, including Apple Home, Amazon Alexa, Google Home, Smart Things, and others.
2. To connect Matter over Thread devices, prepare a Matter hub supporting Thread border router functionality from major platforms.

Kompatible modeller

Oppsett Eksample

• This guide uses Apple Home as an example. Prepare an iPhone (iOS 16.2 or later) or iPad (iPadOS 16.2 or later) with the latest firmware, along with an Apple HomePod mini also running the latest firmware. Connect your iPhone or iPad to your home Wi-Fi network, launch the Apple Home app, and follow Apple’s instructions to set up the HomePod mini.
• For iPhone models 15 and above, no Matter hub is required; they can be added directly.

Legg til tilbehør

• Open the Apple Home app and tap “Add or Scan Accessories.” Add the device to Apple Home by scanning the QR code sticker on the device.
• *You can also activate service via NFC: Simply hold your iPhone 16 or later model near the device’s NFC sensor area to be recognized and activated.

Kontrollenhet
After successfully adding the device to Apple Home, tap the device icon to turn it on or off.

Avanserte funksjoner

Supports creating groups, scenes, and automations, as well as remote control and scheduled control. Devices can also be controlled via Siri voice commands.

Gjenopprett fabrikkinnstillinger

Reset Button Reset
Press and hold the reset button for 15 seconds until the indicator light flashes red rapidly, then release. Within 3 seconds, press the reset button three times briefly. The red light will then switch to slow flashing, indicating the device has begun restoring factory settings. When the indicator light flashes blue rapidly, the restoration is complete.

Slå på tilbakestilling
I tilfelle en strøm outage, use the switch to power on the device for 15 seconds before powering it off. Repeat this power cycle six times consecutively (each cycle consisting of 2 seconds on and 5 seconds off). After the seventh power cycle, the load lamp will flash three times, indicating a successful reset to factory settings.

Oppmerksomhet

• Produktinstallasjon og igangkjøring bør gjøres av en kvalifisert fagperson.
• Our company products are not waterproof or lightning-proof (special models excepted). Please avoid the sun and rain. When installed outdoors, please ensure they are mounted in a waterproof enclosure or in an area equipped with lightning protection devices.
• God varmespredning vil forlenge levetiden til produktene. Sørg for god ventilasjon.
• Vennligst sjekk om arbeidsvoltage brukt samsvarer med parameterkravene til produktene.
• Diameteren på ledningen som brukes må være i stand til å belaste lysarmaturene du kobler til og sikre den faste ledningen.
• Før du slår på produktene, sørg for at alle ledninger er riktige i tilfelle feil tilkobling som forårsaker skade på lysarmaturer.
• Hvis det oppstår en feil, vennligst ikke forsøk å fikse produktene selv. Hvis du har spørsmål, vennligst kontakt leverandørene dine.

Garantiavtale

Garantiperioder fra leveringsdato: 2 år. Gratis reparasjons- eller erstatningstjenester for kvalitetsproblemer tilbys innenfor garantiperioden.

Utelukkelser fra garantien

• Utover garantiperioder.
• Enhver kunstig skade forårsaket av høy voltage, overbelastning eller feil drift.
• Produkter med alvorlig fysisk skade.
• Skader forårsaket av naturkatastrofer og force majeure.

1. Garantietiketter og strekkoder er skadet.
2. No contract signed by our company.